cs4237b Cirrus Logic, Inc., cs4237b Datasheet - Page 40
![no-image](/images/manufacturer_photos/0/1/142/cirrus_logic__inc__sml.jpg)
cs4237b
Manufacturer Part Number
cs4237b
Description
Crystalclear Advanced Audio System With 3d Sound
Manufacturer
Cirrus Logic, Inc.
Datasheet
1.CS4237B.pdf
(114 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
cs4237b-JQ
Manufacturer:
CRYSTAL
Quantity:
246
Company:
Part Number:
cs4237b-KQ
Manufacturer:
CRYSTAL
Quantity:
9
Company:
Part Number:
cs4237b-KQ
Manufacturer:
CRYSTAL
Quantity:
346
Company:
Part Number:
cs4237b-KQ
Manufacturer:
CRYSTAL
Quantity:
329
Part Number:
cs4237b-KQ
Manufacturer:
CRYSTAL
Quantity:
20 000
Caution: This register, except bits CEN and
PEN, can only be written while in Mode Change
Enable (either MCE or PMCE). See the Chang-
ing Sampling Rate section for more details.
Pin Control (I10)
Default = 0000000x
res
IEN
DTM
DEN
OSM1-OSM0
40
XCTL1
D7
XCTL0
D6
Reserved. Must write 0. Could read
as 0 or 1.
Interrupt Enable: This bit enables the
interrupt pin. The Interrupt pin will re-
flect the value of the INT bit of the
Status register (R2). The interrupt
pin is active high.
0 - Interrupt disabled
1 - Interrupt enabled
DMA Timing Mode. MODE 2 & 3 only.
When set, causes the current DMA
request signal to be deasserted on
the rising edge of the IOW or IOR
strobe during the next to last byte of
a DMA transfer. When DTM = 0 the
DMA request is released on the fall-
ing edge of the IOW or IOR during
the last byte of a DMA transfer.
Dither Enable: When set, triangular
pdf dither is added before truncating
the ADC 16-bit value to 8-bit, un-
signed data. Dither is only active in
the 8-bit unsigned data mode.
0 - Dither enabled
1 - Dither disabled
These bits are enabled by setting
SRE = 1 in I22. These bits in com-
bination with DIV5-DIV0 and CS2
(I22) determine the current sample
rate of the WSS Codec when
SRE = 1. Note that these bits can
be disabled by setting IFSE in X11.
OSM1
D5
OSM0 DEN
D4
D3
DTM
D2
D1
IEN
D0
res
XCTL1-XCTL0 XCTL Control: These bits are reflected
Error Status and Initialization (I11, Read Only)
Default = 00000000
ORL1-ORL0
ORR1-ORR0
DRS
COR
D7
PUR
D6
ACI
D5
00 - 12kHz < Fs
01 - Fs > 24kHz
10 - Fs
11 - reserved
on the XCTL1,0 pins of the part.
NOTE: These pins are multiplexed
with other functions; therefore, they
may not be available on a particular
design.
0 - TTL logic low on XCTL1,0 pins
1 - TTL logic high on XCTL1,0 pins
Overrange Left Detect: These bits
determine the overrange on the left
ADC channel. These bits are up-
dated on a sample by sample basis.
0 - Less than -1.5 dB
1 - Between -1.5 dB and 0 dB
2 - Between 0 dB and 1.5 dB
3 - Greater than 1.5 dB overrange
Overrange Right Detect: These bits
determine the overrange on the
Right ADC channel.
0 - Less than -1.5 dB
1 - Between -1.5 dB and 0 dB
2 - Between 0 dB and 1.5 dB
3 - Greater than 1.5 dB overrange
DRQ Status: This bit indicates the
current status of the DRQs assigned
to the WSS Codec.
0 - Capture AND Playback DRQs are
1 - Capture OR Playback DRQs are
overrange
overrange
presently inactive
presently active
DRS
D4
12kHz
ORR1 ORR0
D3
24kHz
D2
CS4237B
ORL1
D1
DS213PP4
ORL0
D0