AN1740 Freescale Semiconductor / Motorola, AN1740 Datasheet - Page 36
AN1740
Manufacturer Part Number
AN1740
Description
Applications Using the Analog Subsystem on MC68HC05JJ/JP Series Microcontrollers
Manufacturer
Freescale Semiconductor / Motorola
Datasheet
1.AN1740.pdf
(80 pages)
- Current page: 36 of 80
- Download datasheet (535Kb)
Application Note
Support Circuitry
Input Divider
36
A number of specific support circuits provide additional capabilities or
options as described in the next subsections.
The primary purpose of the input divider is to extend the common mode
range to allow measurement of pin voltages up to the V
This divider can be switched in between the channel select bus and the
comparator input bus by setting the DHOLD bit and clearing the HOLD
bit in the AMUX register. The input divider can be used only on the
channel select bus signals and cannot be used in conjunction with the
temperature diode. The divider is created with two identical resistances,
each of a nominal 60 k . This provides a divider ratio of 0.5. The
matching of these resistors is within 1%, which results in the divider
ratio varying from 0.49 to 0.51 between different devices.
The input impedance of the comparator is more than 1 M , so the
divider becomes a significant input impedance load when switched into
the signal path. At DC, this input impedance looks like 120 k , but at
frequencies above 10 kHz the 10 pF sample capacitor starts to bypass
the lower leg of the divider and both the input impedance degrades and
the divider ratio starts to drop. Neglecting the parasitic capacitances in
the multiplex circuitry, the input impedance can be roughly modeled as
shown in
Figure
Freescale Semiconductor, Inc.
For More Information On This Product,
9.
Figure 17
Go to: www.freescale.com
R
Figure 17. Divider Equivalent Circuit
MUX
f
c
with typical input impedance as shown previously in
800–2900
MUX
60 k
60 k
R
R
1
2
DHOLD
HOLD
8–13 pF
C
DD
supply level.
MOTOROLA
AN1740
Related parts for AN1740
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
An Overview og the Phase Locked Loop
Manufacturer:
Philips
Datasheet:
Part Number:
Description:
AN OVERVIEW OF THE LPC FLASH INTERFACE
Manufacturer:
STMicroelectronics
Part Number:
Description:
An Evaluation System Interfacing the MPX2000 Series Pressure Sensors to a Microprocessor
Manufacturer:
Motorola / Freescale Semiconductor
Part Number:
Description:
An FM-IF system for DECT and other high speed GFSK applications
Manufacturer:
Philips Semiconductors / NXP Semiconductors
Part Number:
Description:
An 8 x 8 Discrete Cosine Transform on the StarCore SC140/SC1400 Cores
Manufacturer:
Freescale Semiconductor / Motorola
Part Number:
Description:
An Overview of the HCS12 ATD Module
Manufacturer:
Freescale Semiconductor / Motorola
Part Number:
Description:
An Introduction to the External Bus Interface on the HCS12X
Manufacturer:
Freescale Semiconductor / Motorola
Part Number:
Description:
An RF Data Link Using Tango3 and Romeo2 RF Modules
Manufacturer:
Freescale Semiconductor / Motorola
Part Number:
Description:
IC POWER SUPPLY MULT-OUT 44-HSOP
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
IC POWER SUPPLY MULT-OUT 54-SOIC
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
Low-Cost 16-Bit DSP with DDR Controller
Manufacturer:
Freescale Semiconductor / Motorola
Part Number:
Description:
Low-Cost 16-bit DSP with DDR Controller and 10/100 Mbps Ethernet MAC
Manufacturer:
Freescale Semiconductor / Motorola
Datasheet:
Part Number:
Description:
Low-Cost 16-bit DSP with DDR Controller and 10/100 Mbps Ethernet MAC
Manufacturer:
Freescale Semiconductor / Motorola
Datasheet:
Part Number:
Description:
Low-Cost 16-bit DSP with DDR Controller
Manufacturer:
Freescale Semiconductor / Motorola
Datasheet:
Part Number:
Description:
Functional Pin Difference Between the MSC8101 and MPC8260 Communications Processor Modules
Manufacturer:
Freescale Semiconductor / Motorola