FIN1216 Fairchild Semiconductor, FIN1216 Datasheet - Page 6

• Manufacturer Part Number: FIN1216
• Description: Fin1217 * Fin1218 *fin1215 * Fin1216 Lvds 21-bit Serializers/de-serializers
• Manufacturer: Fairchild Semiconductor

www.fairchildsemi.com
Transmitter LVTTL Input Characteristics
V
V
V
I
Transmitter LVDS Output Characteristics (Note 10)
V
'
V
'
I
I
Transmitter Supply Current
I
I
Absolute Maximum Ratings
Transmitter DC Electrical Characteristics
Over supply voltage and operating temperature ranges, unless otherwise specified. (Note 9)
Note 9: All Typical values are at T
Note 10: Positive current values refer to the current flowing into device and negative values means current flowing out of pins. Voltage are referenced to
ground unless otherwise specified (except
Note 11: The power supply current for both transmitter and receiver can be different with the number of active I/O channels.
Note 12: The 16-grayscale test pattern tests device power consumption for a “typical” LCD display pattern. The test pattern approximates signal switching
needed to produce groups of 16 vertical strips across the display.
Power Supply Voltage (V
TTL/CMOS Input/Output Voltage
LVDS Input/Output Voltage
LVDS Output Short Circuit Current (I
Storage Temperature Range (T
Maximum Junction Temperature (T
Lead Temperature (T
ESD Rating (HBM, 1.5 k
ESD Rating (MM, 0
IN
OS
OZ
CCWT
CCPDT
Symbol
IH
IL
IK
OD
V
OS
V
OD
OS
(Soldering, 4 seconds)
LVDS I/O to GND
All Pins (FIN1215, FIN1217 only)
(FIN1215, FIN1217 only)
Input High Voltage
Input Low Voltage
Input Clamp Voltage
Input Current
Output Differential Voltage
V
Offset Voltage
Offset Magnitude Change from Differential LOW-to-HIGH
Short Circuit Output Current
Disabled Output Leakage Current
21:3 Transmitter Power Supply Current
for Worst Case Pattern (With Load)
(Note 11), (Note 12)
Powered Down Supply Current
OD
Magnitude Change from Differential LOW-to-HIGH
:
L
, 200 pF)
)
(85.0 MHz Specification for FIN1217 only)
:
CC
, 100 pF)
A
)
Parameter
25
STG
q
C and with V
'
V
)
J
)
OD
OSD
and V
)
CC
OD

65
).

-0.3V to +4.6V
-0.3V to +4.6V
3.3V.
(Note 7)
0.5V to
q
C to
Continuous
!
10.0 kV

!
!
150
150
260
6.5 kV

400V
4.6V
q
q
q
C
C
C
I
V
V
R
V
DO
R
See Figure 3
PwrDn
IK
IN
IN
OUT
6
L
L
Recommended Operating
Conditions
Note 7: Absolute maximum ratings are DC values beyond which the device
may be damaged or have its useful life impaired. The datasheet specifica-
tions should be met, without exception, to ensure that the system design is
reliable over its power supply, temperature, and output/input loading vari-
ables. Fairchild does not recommend operation outside datasheet specifi-
cations.
Note 8: 100mV V
2 MHz. All the specification below should be met under such a noise.
Supply Voltage (V
Operating Temperature (T
Maximum Supply Noise Voltage

100
100
0.4V to 4.6V
GND
0V to 4.6V, PwrDn
18 mA
(V
Test Conditions
0V
CCNPP
0.8V
:
:
, See Figure 1
,
)
CC
noise should be tested for frequency at least up to
33.0 MHz
40.0 MHz
65.0 MHz
85.0 MHz
CC
0V
)
A
)(Note 7)

1.125
GND
Min
250
2.0
10.0

1.25

r
28.0
29.0
34.0
39.0
10.0
Typ
0.79
1.8
3.5
1.0
0
100 mV

1.375
r
40°C to
Max
V

10.0
35.0

46.2
51.7
57.2
62.7
55.0
450
0.8
10.0
1.5
5.0
CC
3.0V to 3.6V
P-P
(Note 8)

Units
85°C
mV
mV
mV
mA
mA
P
P
P
V
V
V
V
A
A
A