TMPM382FSFG Toshiba, TMPM382FSFG Datasheet - Page 26

• Manufacturer Part Number: TMPM382FSFG
• Manufacturer: Toshiba

Specifications of TMPM382FSFG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 64K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 64
• Package: QFP(14x14)
• Vcc: 5V
• Cpu Mhz: 40
• Ssp (ch) Spi: 1
• I2c/sio (ch): 1
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 10
• 16-bit Timer / Counter: 6
• Motor / Igbt Control: Y
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit

4 Dubug Interface
4.5
4.5.1
4.5.2
The table 4-2 below summarizes the debug interface pin functions and related port settings after reset.
Table 4-3 Debug Interface
Table 4-2 Debug interface pins and port setting after reset
○：Enable、×：Disable (Can use general purpose port)
When using a low power consumption mode, take note of the following points.
JTAG+SW (After RESET)
JTAG+SW (No TRST
JTAG+TRACE
SW
SW+SWV
Disable Debug function
DEBUG
DEBUG
DEBUG
DEBUG
DEBUG
Setting
PORT
PORT
PORT
Initial
Connection with a Debug Tool
registers be sure their settings.
MCU will be unable to control signals received from the debugging tools and can not continue
debugging. According to the usage of the debug interface pins, be sure their settings.
(Note 1) If PB3 and PB5 are configured as debug function pins, output continues to be enabled
(Note 2) If PB4 is configured as a debug function pin, it prevents a low power consumption mode
When debugging, do not change setting debug interface to general purpose port by program. Then,
For how to connect a debug tool, refer to the method recommended by each manufacturer.
Debug interface pins have pull-up or pull-down register. When connect with pull-up or pull-down
How to connect
When use general purpose port
even in STOP mode regardless of the setting of the CGSTBYCR<DRVE> .
from being fully effective. Configure PB4 to function as a general-purpose port if the
debug function is not used.
name)
PORT
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
(Bit
------------------
)
Debug Function
TARCEDATA0
TRACEDATA1
TCK/SWCLK
TMS/SWDIO
TRACECLK
TDO/SWV
------------------
TRST
---------------
TRST
○
×
○
×
×
×
TDI
TMPM380/M382 - 2 / 3 -
TDI
○
○
○
×
×
×
TDO/
SWV
Function
(PBFR)
○
○
○
×
○
×
0
0
0
1
1
1
1
1
Using Debug Interface pins
SWCLK
TCK/
○
○
○
○
○
×
(PBIE)
Input
0
0
0
1
1
0
1
1
Port Setting After Reset
SWDIO
TMS/
○
○
○
○
○
×
(PBCR)
Output
0
0
0
0
1
0
1
0
TRACE
DATA1
×
×
○
×
×
×
(PBPUP)
Pull-up
0
0
0
1
0
0
1
1
TMPM380/M382
TARCE
DATA0
×
×
○
×
×
×
Pull-down
(PBPDN)
TRACE
CLK
0
0
0
0
1
0
0
0
○
×
×
×
×
×