LPC2468 NXP Semiconductors, LPC2468 Datasheet - Page 41

no-image

LPC2468

Manufacturer Part Number
LPC2468
Description
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LPC2468FBD
Manufacturer:
NXP
Quantity:
5 000
Part Number:
LPC2468FBD
Manufacturer:
NXP
Quantity:
26
Part Number:
LPC2468FBD208
Manufacturer:
FUJI
Quantity:
100
Part Number:
LPC2468FBD208
Manufacturer:
NXP
Quantity:
5 000
Part Number:
LPC2468FBD208
Manufacturer:
NXP
Quantity:
26
Part Number:
LPC2468FBD208
Manufacturer:
NXP
Quantity:
20 000
Part Number:
LPC2468FBD208
Manufacturer:
NXP/恩智浦
Quantity:
1 300
Part Number:
LPC2468FBD208
0
Company:
Part Number:
LPC2468FBD208
Quantity:
600
Part Number:
LPC2468FBD208+551
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC2468FBD208,551
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
LPC2468FBD208.551
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
LPC2468FBD208K
Manufacturer:
NXP/恩智浦
Quantity:
3 000
Part Number:
LPC2468FBD208K
0
NXP Semiconductors
LPC2468
Product data sheet
7.25.1.3 RTC oscillator
7.25.2 PLL
7.25.3 Wake-up timer
PLLCLKIN and CCLK are the same value unless the PLL is active and connected. The
clock frequency for each peripheral can be selected individually and is referred to as
PCLK. Refer to
The RTC oscillator can be used as the clock source for the RTC and/or the WDT. Also, the
RTC oscillator can be used to drive the PLL and the CPU.
The PLL accepts an input clock frequency in the range of 32 kHz to 25 MHz. The input
frequency is multiplied up to a high frequency, then divided down to provide the actual
clock used by the CPU and the USB block.
The PLL input, in the range of 32 kHz to 25 MHz, may initially be divided down by a value
‘N’, which may be in the range of 1 to 256. This input division provides a wide range of
output frequencies from the same input frequency.
Following the PLL input divider is the PLL multiplier. This can multiply the input divider
output through the use of a Current Controlled Oscillator (CCO) by a value ‘M’, in the
range of 1 through 32768. The resulting frequency must be in the range of 275 MHz to
550 MHz. The multiplier works by dividing the CCO output by the value of M, then using a
phase-frequency detector to compare the divided CCO output to the multiplier input. The
error value is used to adjust the CCO frequency.
The PLL is turned off and bypassed following a chip Reset and by entering Power-down
mode. PLL is enabled by software only. The program must configure and activate the PLL,
wait for the PLL to lock, then connect to the PLL as a clock source.
The LPC2468 begins operation at power-up and when awakened from Power-down and
Deep power-down modes by using the 4 MHz IRC oscillator as the clock source. This
allows chip operation to resume quickly. If the main oscillator or the PLL is needed by the
application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
When the main oscillator is initially activated, the Wake-up Timer allows software to
ensure that the main oscillator is fully functional before the processor uses it as a clock
source and starts to execute instructions. This is important at power on, all types of Reset,
and whenever any of the aforementioned functions are turned off for any reason. Since
the oscillator and other functions are turned off during Power-down and Deep power-down
modes, any wake-up of the processor from Power-down modes makes use of the
Wake-up Timer.
The Wake-up Timer monitors the crystal oscillator to check whether it is safe to begin
code execution. When power is applied to the chip, or when some event caused the chip
to exit Power-down mode, some time is required for the oscillator to produce a signal of
sufficient amplitude to drive the clock logic. The amount of time depends on many factors,
including the rate of V
electrical characteristics (if a quartz crystal is used), as well as any other external circuitry
(e.g., capacitors), and the characteristics of the oscillator itself under the existing ambient
conditions.
All information provided in this document is subject to legal disclaimers.
Section 7.25.2
Rev. 6.1 — 6 September 2011
DD(3V3)
ramp (in the case of power on), the type of crystal and its
for additional information.
Single-chip 16-bit/32-bit micro
LPC2468
© NXP B.V. 2011. All rights reserved.
41 of 85

Related parts for LPC2468