ATmega32A Atmel Corporation, ATmega32A Datasheet - Page 40

• Manufacturer Part Number: ATmega32A
• Manufacturer: Atmel Corporation

Specifications of ATmega32A

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.2.2
10.2.3
8155C–AVR–02/11
External Reset
Brown-out Detection
Figure 10-3. MCU Start-up, RESET Extended Externally
An External Reset is generated by a low level on the RESET pin. Reset pulses longer than the
minimum pulse width (see
reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset.
When the applied signal reaches the Reset Threshold Voltage – V
delay counter starts the MCU after the Time-out period t
Figure 10-4. External Reset During Operation
ATmega32A has an On-chip Brown-out Detection (BOD) circuit for monitoring the V
ing operation by comparing it to a fixed trigger level. The trigger level for the BOD can be
selected by the fuse BODLEVEL to be 2.7V (BODLEVEL unprogrammed), or 4.0V (BODLEVEL
programmed). The trigger level has a hysteresis to ensure spike free Brown-out Detection. The
hysteresis on the detection level should be interpreted as V
V
The BOD circuit can be enabled/disabled by the fuse BODEN. When the BOD is enabled
(BODEN programmed), and V
5), the Brown-out Reset is immediately activated. When V
(V
expired.
The BOD circuit will only detect a drop in V
ger than t
BOT
BOT+
- V
in
INTERNAL
TIME-OUT
HYST
BOD
Figure
RESET
RESET
V
/2.
CC
given in
CC
10-5), the delay counter starts the MCU after the Time-out period t
“System and Reset Characteristics” on page
“System and Reset Characteristics” on page
V
CC
POT
decreases to a value below the trigger level (V
CC
if the voltage stays below the trigger level for lon-
V
RST
t
TOUT
TOUT
CC
has expired.
BOT+
increases above the trigger level
= V
RST
299.
BOT
– on its positive edge, the
ATmega32A
+ V
299) will generate a
HYST
BOT-
/2 and V
in
CC
Figure 10-
level dur-
TOUT
BOT-
has
40
=