ATmega32A Atmel Corporation, ATmega32A Datasheet - Page 117

• Manufacturer Part Number: ATmega32A
• Manufacturer: Atmel Corporation

Specifications of ATmega32A

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

16.10.7
16.10.8
8155C–AVR–02/11
TIMSK – Timer/Counter Interrupt Mask Register
TIFR – Timer/Counter Interrupt Flag Register
The Input Capture is updated with the counter (TCNT1) value each time an event occurs on the
ICP1 pin (or optionally on the analog comparator output for Timer/Counter1). The Input Capture
can be used for defining the counter TOP value.
The Input Capture Register is 16-bit in size. To ensure that both the high and low bytes are read
simultaneously when the CPU accesses these registers, the access is performed using an 8-bit
temporary High Byte Register (TEMP). This temporary register is shared by all the other 16-bit
registers.
Note:
• Bit 5 – TICIE1: Timer/Counter1, Input Capture Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Counter1 Input Capture Interrupt is enabled. The corresponding Interrupt
Vector
• Bit 4 – OCIE1A: Timer/Counter1, Output Compare A Match Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Counter1 Output Compare A match interrupt is enabled. The corresponding
Interrupt Vector
TIFR, is set.
• Bit 3 – OCIE1B: Timer/Counter1, Output Compare B Match Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Counter1 Output Compare B match interrupt is enabled. The corresponding
Interrupt Vector
TIFR, is set.
• Bit 2 – TOIE1: Timer/Counter1, Overflow Interrupt Enable
When this bit is written to one, and the I-flag in the Status Register is set (interrupts globally
enabled), the Timer/Counter1 Overflow Interrupt is enabled. The corresponding Interrupt Vector
(See “Interrupts” on page
Note:
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
(See “Interrupts” on page
1. This register contains interrupt control bits for several Timer/Counters, but only Timer1 bits are
1. This register contains flag bits for several Timer/Counters, but only Timer1 bits are described
See “Accessing 16-bit Registers” on page 94.
described in this section. The remaining bits are described in their respective timer sections.
in this section. The remaining bits are described in their respective timer sections.
OCIE2
OCF2
R/W
R/W
(See “Interrupts” on page
(See “Interrupts” on page
7
0
7
0
TOIE2
TOV2
R/W
R/W
45.) is executed when the TOV1 Flag, located in TIFR, is set.
6
0
6
0
45.) is executed when the ICF1 Flag, located in TIFR, is set.
TICIE1
R/W
ICF1
R/W
(1)
5
0
5
0
OCIE1A
OCF1A
R/W
R/W
45.) is executed when the OCF1A Flag, located in
45.) is executed when the OCF1B Flag, located in
4
0
4
0
OCIE1B
OCF1B
R/W
R/W
3
0
3
0
TOIE1
TOV1
R/W
R/W
2
0
2
0
OCIE0
OCF0
R/W
R/W
1
0
1
0
ATmega32A
TOIE0
TOV0
R/W
R/W
0
0
0
0
TIMSK
TIFR
117