ATmega16HVB Atmel Corporation, ATmega16HVB Datasheet - Page 117

• Manufacturer Part Number: ATmega16HVB
• Manufacturer: Atmel Corporation

Specifications of ATmega16HVB

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 8 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 17
• Ext Interrupts: 15
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 4.0 to 25
• Operating Voltage (vcc): 4.0 to 25
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

20.3.1
8042D–AVR–10/11
Configuring PA1 and PA0 for V-ADC operation
Power-off mode. Note that the bandgap voltage reference must be enabled and disabled sepa-
rately, see
Figure 20-2. Voltage ADC conversion diagram.
To perform a V-ADC conversion, the analog input channel must first be selected by writing to the
VADMUX register. When a logical one is written to the V-ADC Start Conversion bit VADSC, a
conversion of the selected channel will start. The VADSC bit stays high as long as the conver-
sion is in progress and will be cleared by hardware when the conversion is completed. When a
conversion is in progress, the V-ADC Data Register - VADCL and VADCH will be invalid. If the
System Clock Prescaler setting is changed during a V-ADC conversion, the conversion will be
aborted. If a different data channel is selected while a conversion is in progress, the ADC will fin-
ish the current conversion before performing the channel change. When a conversion is finished
the V-ADC Conversion Complete Interrupt Flag – VADCCIF is set. One 12-bit conversion takes
519µs to complete from the start bit is set to the interrupt flag is set. The V-ADC Data Register -
VADCL and VADCH will be valid until a new conversion is started. To ensure that correct data is
read, both high and low byte data registers should be read before starting a new conversion.
When one of the single ended channels ADC0 or ADC1 is used as analog input to the VADC,
either PA0 or PA1 are used as signal ground (SGND). When ADC0/1 is selected as input chan-
nel, PA1/0 is automatically switched to SGND.
The use of PA1 and PA0 as SGND is efficient for the thermistor configuration shown in
ing circuit” on page
divider resistor, R31, to PA0 and PA1 respectively.
Both PA0 and PA1 have very high input impedance when used as ADC inputs, which makes it
possible to connect two thermistors in the configuration, shown in
220. However, input impedance is limited and if high accuracy is required, only one thermistor
should be connected between PA0 and PA1. If two thermistors are connected, the configuration
is as follows:
• When measuring RT33, PA1 should be used as input channel and PA0 is automatically
• When measuring RT32, PA0 should be used as input channel and PA1 is automatically
switched to SGND
switched to SGND
Conversion Result
Start Conversion
”Bandgap calibration” on page
Interrupt
OLD DATA
220. Both thermistors, RT32 and RT33 are connected through a common
INVALID DATA
519µs
123.
ATmega16HVB/32HVB
V A L I D
D ATA
”Operating circuit” on page
INVALID DATA
”Operat-
117