AT90CAN64 Atmel Corporation, AT90CAN64 Datasheet - Page 256

• Manufacturer Part Number: AT90CAN64
• Manufacturer: Atmel Corporation

Specifications of AT90CAN64

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Can: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19.10.5
256
AT90CAN32/64/128
CAN Enable MOb Registers -
CANEN2 and CANEN1
• Bit 3 – ENERR: Enable MOb Errors Interrupt
• Bit 2 – ENBX: Enable Frame Buffer Interrupt
• Bit 1 – ENERG: Enable General Errors Interrupt
• Bit 0 – ENOVRT: Enable CAN Timer Overrun Interrupt
• Bits 14:0 - ENMOB14:0: Enable MOb
This bit provides the availability of the MOb.
It is set to one when the MOb is enabled (i.e. CONMOB1:0 of CANCDMOB register).
Once TXOK or RXOK is set to one (TXOK for automatic reply), the corresponding ENMOB is
reset. ENMOB is also set to zero configuring the MOb in disabled mode, applying abortion or
standby mode.
• Bit 15 – Reserved Bit
This bit is reserved for future use.
Initial Value
Initial Value
Read/Write
Read/Write
Bit
Bit
– 1- transmit interrupt enabled.
– 0 - interrupt disabled.
– 1- MOb errors interrupt enabled.
– 0 - interrupt disabled.
– 1- frame buffer interrupt enabled.
– 0 - interrupt disabled.
– 1- general errors interrupt enabled.
– 0 - interrupt disabled.
– 1- CAN timer interrupt overrun enabled.
– 0 - message object disabled: MOb available for a new transmission or reception.
– 1 - message object enabled: MOb in use.
ENMOB7 ENMOB6
15
R
7
0
-
-
-
ENMOB14 ENMOB13 ENMOB12 ENMOB11 ENMOB10 ENMOB9
14
R
R
6
0
0
ENMOB5
13
R
R
5
0
0
ENMOB4
12
R
R
4
0
0
ENMOB3
11
R
R
3
0
0
ENMOB2
10
R
R
2
0
0
ENMOB1
R
R
1
9
0
0
ENMOB0
ENMOB8
R
R
0
8
0
0
CANEN2
CANEN1
7679H–CAN–08/08