AT90CAN64 Atmel Corporation, AT90CAN64 Datasheet - Page 181
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT90CAN64
Manufacturer Part Number
AT90CAN64
Description
Manufacturer
Atmel Corporation
Specifications of AT90CAN64
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
53
Ext Interrupts
8
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
2
Can
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
4
Output Compare Channels
8
Input Capture Channels
2
Pwm Channels
7
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT90CAN64-15AT
Manufacturer:
Atmel
Quantity:
3 327
Company:
Part Number:
AT90CAN64-15AT1
Manufacturer:
Atmel
Quantity:
1 985
Company:
Part Number:
AT90CAN64-15AZ
Manufacturer:
Atmel
Quantity:
1 995
Company:
Part Number:
AT90CAN64-15MT
Manufacturer:
Freescale
Quantity:
100
Company:
Part Number:
AT90CAN64-15MT1
Manufacturer:
Atmel
Quantity:
7 775
Part Number:
AT90CAN64-15MT1
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT90CAN64-16AU
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
AT90CAN64-16MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
17.4.4
17.5
17.5.1
7679H–CAN–08/08
Serial Frame
Synchronous Clock Operation
Frame Formats
Note that
to add some margin to avoid possible loss of data due to frequency variations.
When synchronous mode is used (UMSELn = 1), the XCKn pin will be used as either clock input
(Slave) or clock output (Master). The dependency between the clock edges and data sampling
or data change is the same. The basic principle is that data input (on RxDn) is sampled at the
opposite XCKn clock edge of the edge the data output (TxDn) is changed.
Figure 17-3. Synchronous Mode XCKn Timing.
The UCPOLn bit UCRSnC selects which XCKn clock edge is used for data sampling and which
is used for data change. As
at rising XCKn edge and sampled at falling XCKn edge. If UCPOLn is set, the data will be
changed at falling XCKn edge and sampled at rising XCKn edge.
A serial frame is defined to be one character of data bits with synchronization bits (start and stop
bits), and optionally a parity bit for error checking.
The USARTn accepts all 30 combinations of the following as valid frame formats:
A frame starts with the start bit followed by the least significant data bit. Then the next data bits,
up to a total of nine, are succeeding, ending with the most significant bit. If enabled, the parity bit
is inserted after the data bits, before the stop bits. When a complete frame is transmitted, it can
be directly followed by a new frame, or the communication line can be set to an idle (high) state.
Figure 17-4
optional.
• 1 start bit
• 5, 6, 7, 8, or 9 data bits
• no, even or odd parity bit
• 1 or 2 stop bits
f
clk
UCPOLn = 1
UCPOLn = 0
illustrates the possible combinations of the frame formats. Bits inside brackets are
io
depends on the stability of the system clock source. It is therefore recommended
RxDn / TxDn
RxDn / TxDn
XCKn
XCKn
Figure 17-3
shows, when UCPOLn is zero the data will be changed
AT90CAN32/64/128
Sample
Sample
181