AT32UC3B1128 Atmel Corporation, AT32UC3B1128 Datasheet - Page 337

• Manufacturer Part Number: AT32UC3B1128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B1128

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 28
• Ext Interrupts: 28
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• RIIC: Ring Indicator Input Change Flag
• NACK: Non Acknowledge
• RXBUFF: Reception Buffer Full
• ITER/UNRE: Max number of Repetitions Reached or SPI Underrun Error
• TXEMPTY: Transmitter Empty
• TIMEOUT: Receiver Time-out
• PARE: Parity Error
• FRAME: Framing Error
• OVRE: Overrun Error
• RXBRK: Break Received/End of Break
• TXRDY: Transmitter Ready
• RXRDY: Receiver Ready
32059L–AVR32–01/2012
0: No change has been detected on the RI pin since the last CSR read.
1: At least one change has been detected on the RI pin since the last CSR read.
0: No Non Acknowledge has been detected since the last RSTNACK.
1: At least one Non Acknowledge has been detected since the last RSTNACK.
This bit is cleared by writing a one to CR.RSTNACK.
0: The Buffer Full signal from the Peripheral DMA Controller channel is inactive.
1: The Buffer Full signal from the Peripheral DMA Controller channel is active.
If USART does not operate in SPI Slave Mode:
ITER=0: Maximum number of repetitions has not been reached since the last RSTSTA.
ITER=1: Maximum number of repetitions has been reached since the last RSTSTA.
If USART operates in SPI Slave Mode:
UNRE=0: No SPI underrun error has occurred since the last RSTSTA.
UNRE=1: At least one SPI underrun error has occurred since the last RSTSTA.
This bit is cleared by writing a one to CR.RSTSTA.
0: The transmitter is either disabled or there are characters in THR, or in the transmit shift register.
1: There are no characters in neither THR, nor in the transmit shift register.
This bit is cleared by writing a one to CR.STTBRK.
0: There has not been a time-out since the last Start Time-out command (CR.STTTO), or RTOR.TO is zero.
1: There has been a time-out since the last Start Time-out command.
This bit is cleared by writing a one to CR.STTTO or CR.RETTO.
0: Either no parity error has been detected, or the parity bit is a zero in multidrop mode, since the last RSTSTA.
1: Either at least one parity error has been detected, or the parity bit is a one in multidrop mode, since the last RSTSTA.
This bit is cleared by writing a one to CR.RSTSTA.
0: No stop bit has been found as low since the last RSTSTA.
1: At least one stop bit has been found as low since the last RSTSTA.
This bit is cleared by writing a one to CR.RSTSTA.
0: No overrun error has occurred since the last RSTSTA.
1: At least one overrun error has occurred since the last RSTSTA.
This bit is cleared by writing a one to CR.RSTSTA.
0: No Break received or End of Break detected since the last RSTSTA.
1: Break received or End of Break detected since the last RSTSTA.
This bit is cleared by writing a one to CR.RSTSTA.
0: The transmitter is either disabled, or a character in THR is waiting to be transferred to the transmit shift register, or an
STTBRK command has been requested. As soon as the transmitter is enabled, TXRDY is set.
1: There is no character in the THR.
This bit is cleared by writing a one to CR.STTBRK.
0: The receiver is either disabled, or no complete character has been received since the last read of RHR. If characters were
being received when the receiver was disabled, RXRDY changes to 1 when the receiver is enabled.
1: At least one complete character has been received and RHR has not yet been read.
337