AT32UC3A4128 Atmel Corporation, AT32UC3A4128 Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT32UC3A4128
Manufacturer Part Number
AT32UC3A4128
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(33 pages)
3.AT32UC3A0128.pdf
(159 pages)
4.AT32UC3A3128.pdf
(91 pages)
5.AT32UC3A3128.pdf
(1012 pages)
Specifications of AT32UC3A4128
Flash (kbytes)
128 Kbytes
Pin Count
100
Max. Operating Frequency
66 MHz
Cpu
32-bit AVR
Hardware Qtouch Acquisition
No
Usb Transceiver
1
Usb Speed
Hi-Speed
Usb Interface
Device + OTG
Spi
6
Twi (i2c)
2
Uart
4
Sd / Emmc
2
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0 to 3.6
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3A4128S-C1UR
Manufacturer:
ATMEL
Quantity:
2 620
Company:
Part Number:
AT32UC3A4128S-CIUT
Manufacturer:
ATMEL
Quantity:
350
Part Number:
AT32UC3A4128S-CIUT
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
AT32UC3A4128S-U
Manufacturer:
ATMEL
Quantity:
12 914
Company:
Part Number:
AT32UC3A4128SC101
Manufacturer:
STM
Quantity:
6 278
Company:
Part Number:
AT32UC3A4128SC1UT
Manufacturer:
ATMEL
Quantity:
6 055
AVR32
If several events occur on the same instruction, they are handled in a prioritized way. The priority
ordering is presented in Table 3-4. If events occur on several instructions at different locations in
the pipeline, the events on the oldest instruction are always handled before any events on any
younger instruction, even if the younger instruction has events of higher priority than the oldest
instruction. An instruction B is younger than an instruction A if it was sent down the pipeline later
than A.
The addresses and priority of simultaneous events are shown in
Table 3-4 on page
28. Some of
the exceptions are unused in AVR32UC since it has no MMU or coprocessor interface.
The interrupt system requires that an interrupt controller is present outside the core in order to
prioritize requests and generate a correct offset if more than one interrupt source exists for each
priority level. An interrupt controller generating different offsets depending on interrupt request
source is referred to as autovectoring. Note that the interrupt controller should generate
autovector addresses that do not conflict with addresses in use by other events or regular pro-
gram code.
The addresses of the interrupt routines are calculated by adding the address on the autovector
offset bus to the value of the Exception Vector Base Address (EVBA). The INT0, INT1, INT2,
INT3, and NMI signals indicate the priority of the pending interrupt. INT0 has the lowest priority,
and NMI the highest priority of the interrupts.
27
32002F–03/2010