AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 752

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
36.9.3
MEMORY_SERVICE
For any operation, the full 7 bits of the address must be provided. For write operations, 32 data
bits must be provided, or the result will be undefined. For read operations, shifting may be termi-
nated once the required number of bits have been acquired.
Table 36-5.
This instruction allows access to registers in an optional Memory Service unit. Memory Service
registers are addressed by their register index, as listed in the Memory Service documentation.
The 7-bit register index and a read/write control bit, and the 32-bit data is accessed through the
JTAG port.
The Memory Service unit may offer features such as CRC calculation of memory, debug trace
support, and test features. Please refer to the Memory Service Unit documentation and the part
specific documentation for details.
The data register is alternately interpreted by the SAB as an address register and a data regis-
ter. The SAB starts in address mode after the MEMORY_SERVICE instruction is selected, and
toggles between address and data mode each time a data scan completes with the busy bit
cleared.
Starting in Run-Test/Idle, Memory Service registers are accessed in the following way:
Instructions
IR input value
IR output value
DR Size
DR input value (Address phase)
DR input value (Data read phase)
DR input value (Data write phase)
DR output value (Address phase)
DR output value (Data read phase)
DR output value (Data write phase)
1. Select the DR Scan path.
2. Scan in the 7-bit address for the Memory Service register and a direction bit (1=read,
3. Go to Update-DR and re-enter Select-DR Scan.
4. For a read operation, scan out the contents of the addressed register. For a write oper-
5. Return to Run-Test/Idle.
0=write).
ation, scan in the new contents of the register.
NEXUS_ACCESS details
Details
10000 (0x10)
peb01
34 bits
aaaaaaar xxxxxxxx xxxxxxxx xxxxxxxx xx
xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xx
dddddddd dddddddd dddddddd dddddddd xx
xx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxeb
eb dddddddd dddddddd dddddddd dddddddd
xx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxeb
AT32UC3A
752