AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 458

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
29.7.2
Register Name:
Access Type:
• SPD: Speed
Set to 1 to indicate 100 Mbit/s operation, 0 for 10 Mbit/s. The value of this pin is reflected on the speed pin.
• FD: Full Duplex
If set to 1, the transmit block ignores the state of collision and carrier sense and allows receive while transmitting. Also con-
trols the half_duplex pin.
• Bit rate:
If set to 1 to configure the interface for serial operation. Must be set before receive and transmit enable in the network con-
trol register. If set a serial interface is configured with transmit and receive data being driven out on txd[0] and received on
rxd[0] serially. Also the crs and rx_dv are logically ORed together so either may be used as the data valid signal.
• CAF: Copy All Frames
When set to 1, all valid frames are received.
• JFRAME: Jumbo Frames
Set to one to enable jumbo frames of up to 10240 bytes to be accepted.
• NBC: No Broadcast
When set to 1, frames addressed to the broadcast address of all ones are not received.
• MTI: Multicast Hash Enable
When set, multicast frames are received when the 6-bit hash function of the destination address points to a bit that is set in
the hash register.
• UNI: Unicast Hash Enable
When set, unicast frames are received when the 6-bit hash function of the destination address points to a bit that is set in
the hash register.
• BIG: Receive 1536 bytes frames
Setting this bit means the MACB receives frames up to 1536 bytes in length. Normally, the MACB would reject any frame
above 1518 bytes.
• EAE: External address match enable
When set, the eam pin can be used to copy frames to memory.
UNI
31
23
15
–
–
7
Network Configuration Register
RBOF
MTI
30
22
14
NCFGR
–
–
6
Read/Write
NBC
PAE
29
21
13
–
–
5
RTY
CAF
28
20
12
–
–
4
JFRAME
IRXFCS
27
19
11
–
3
CLK
EFRHD
Bit rate
26
18
10
–
2
DRFCS
EAE
FD
25
17
–
9
1
AT32UC3A
RLCE
SPD
BIG
24
16
–
8
0
458