AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 172

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
22.4.2
22.4.3
22.4.4
22.4.5
22.4.6
I/O Line or Peripheral Function Selection
Peripheral Selection
Output Control
Open Drain Mode
Inputs
When a pin is multiplexed with one or more peripheral functions, the selection is controlled with
the register GPER. If a bit in the register is set, the corresponding pin is controlled by the GPIO.
If a bit is cleared, the corresponding pin is controlled by a peripheral function.
The GPIO provides multiplexing of up to four peripheral functions on a single pin. The selection
is performed by accessing PMR0 (Peripheral Mux Register 0) and PMR1 (Peripheral Mux Regis-
ter 1).
When the I/O line is assigned to a peripheral function, i.e. the corresponding bit in GPER is at 0,
the drive of the I/O line is controlled by the peripheral. The peripheral, depending on the value in
PMR0 and PMR1, determines whether the pin is driven or not.
When the I/O line is controlled by the GPIO, the value of ODER (Output Driver Enable Register)
determines if the pin is driven or not. When a bit in this register is at 1, the corresponding I/O line
is driven by the GPIO. When the bit is at 0, the GPIO does not drive the line.
The level driven on an I/O line can be determined by writing OVR (Output Value Register).
Each I/O line can be independently programmed to operate in open drain mode. This feature
permits several drivers to be connected on the I/O line. The drivers should only actively drive the
line low. An external pull-up resistor (or enabling the internal one) is generally required to guar-
antee a high level on the line when no driver is active.
The Open Drain feature is controlled by ODMER (Open Drain Mode Enable Register). The Open
Drain mode can be selected whether the I/O line is controlled by the GPIO or assigned to a
peripheral function.
The level on each I/O line can be read through PVR (Pin Value Register). This register indicates
the level of the I/O lines regardless of whether the lines are driven by the GPIO or by an external
component. Note that due to power saving measures, PVR register can only be read when
GPER is set for the corresponding pin or if interrupt is enabled for the pin.
Output Line Timings
The figure below shows the timing of the I/O line when setting and clearing the Output Value
Register by accessing OVR. The same timing applies when performing a ‘set’ or ‘clear’ access
i.e. writing to OVRS or OVRC. The timing of PVR (Pin Value Register) is also shown.
AT32UC3A
172