AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 57

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

O s c 1
c lo c k
32058K AVR32-01/12
O s c 0
13.5.4.1
c lo c k
P L L O S C
0
1
Enabling the PLL
D iv id e r
P L L D I V
I n p u t
divide the output of the PLL by two and bring the clock in range of the max frequency of the
CPU.
When the PLL is switched on, or when changing the clock source or multiplication factor for the
PLL, the PLL is unlocked and the output frequency is undefined. The PLL clock for the digital
logic is automatically masked when the PLL is unlocked, to prevent connected digital logic from
receiving a too high frequency and thus become unstable.
Figure 13-3. PLL with control logic and filters
PLLn is enabled by writing the PLLEN bit in the PLLn register. PLLOSC selects Oscillator 0 or 1
as clock source. The PLLMUL and PLLDIV bitfields must be written with the multiplication and
division factors, respectively, creating the voltage controlled ocillator frequency f
frequency f
If PLLOPT[1] field is set to 0:
If PLLOPT[1] field is set to 1:
The PLLn:PLLOPT field should be set to proper values according to the PLL operating fre-
quency. The PLLOPT field can also be set to divide the output frequency of the PLLs by 2.
The lock signal for each PLL is available as a LOCKn flag in POSCSR. An interrupt can be gen-
erated on a 0 to 1 transition of these bits.
f
f
f
f
VCO
VCO
PLL
PLL
= f
= f
= (PLLMUL+1)/(PLLDIV) • f
= 2*(PLLMUL+1) • f
PLL
D iv id e r
O u t p u t
D e t e c t o r
P L L M U L
VCO.
VCO
P h a s e
:
/ 2
.
P L L O P T
V C O
OSC
if PLLDIV = 0.
f
OSC
v c o
if PLLDIV > 0.
D e t e c t o r
1 / 2
L o c k
P L L O P T [ 1 ]
0
1
f
P L L
M a s k
AT32UC3A
VCO
L o c k b it
and the PLL
P L L c lo c k
57