MT46H32M16LFBF-6 AT:C Micron Technology Inc, MT46H32M16LFBF-6 AT:C Datasheet - Page 18

• Manufacturer Part Number: MT46H32M16LFBF-6 AT:C
• Manufacturer: Micron Technology Inc

Specifications of MT46H32M16LFBF-6 AT:C

• Lead Free Status / Rohs Status: Supplier Unconfirmed

Table 5: AC/DC Electrical Characteristics and Operating Conditions (Continued)
Notes 1–5 apply to all parameters/conditions in this table; V
PDF: 09005aef83dd2b3e
t67m_512mb_mobile_lpddr.pdf - Rev. E 6/11 EN
Parameter/Condition
Output leakage current
(DQ are disabled; 0V ≤ V
Operating temperature
Commercial
Industrial
Automotive
Notes:
OUT
≤ V
10. CK and CK# input slew rate must be ≥1 V/ns (2 V/ns if measured differentially).
11. V
12. The value of V
13. DQ and DM input slew rates must not deviate from DQS by more than 10%. 50ps must
1. All voltages referenced to V
2. All parameters assume proper device initialization.
3. Tests for AC timing, I
4. Outputs measured with equivalent load; transmission line delay is assumed to be very
5. Timing and I
6. Any positive glitch must be less than one-third of the clock cycle and not more than
7. V
8. To maintain a valid level, the transitioning edge of the input must:
9. V
DDQ
nominal supply voltage levels, but the related specifications and device operation are
guaranteed for the full voltage range specified.
small:
but input timing is still referenced to V
output timing reference voltage level is V
+200mV or 2.0V, whichever is less. Any negative glitch must be less than one-third of
the clock cycle and not exceed either –150mV or +1.6V, whichever is more positive.
8a. Sustain a constant slew rate from the current AC level through to the target AC lev-
el, V
8b. Reach at least the target AC level.
8c. After the AC target level is reached, continue to maintain at least the target DC lev-
el, V
be greater than one-third of the cycle rate. V
width ≤3ns and the pulse width cannot be greater than one-third of the cycle rate.
el on CK#.
variations in the DC level of the same.
be added to
4 V/ns, functionality is uncertain.
)
DD
IH
ID
I/O
overshoot: V
is the magnitude of the difference between the input level on CK and the input lev-
and V
IL(AC)
IL(DC)
Full drive strength
Or V
or V
DDQ
50
DD
t
DS and
IH(DC)
IH(AC)
must track each other and V
IX
tests may use a V
IHmax
is expected to equal V
Symbol
.
.
I
T
T
T
DD
t
OZ
= V
DH for each 100 mV/ns reduction in slew rate. If slew rate exceeds
A
A
A
20pF
, and electrical AC and DC characteristics may be conducted at
DDQ
DD
18
/V
SS
+ 1.0V for a pulse width ≤3ns and the pulse width cannot
DDQ
.
I/O
512Mb: x16, x32 Mobile LPDDR SDRAM
IL
Half drive strength
= 1.70–1.95V
-to-V
Min
–40
–40
Micron Technology, Inc. reserves the right to change products or specifications without notice.
–5
0
DDQ/2
IH
DDQ
50
swing of up to 1.5V in the test environment,
DDQ
/2 (or to the crossing point for CK/CK#). The
DDQ
of the transmitting device and must track
IL
/2.
must be less than or equal to V
undershoot: V
10pF
+105
Max
Electrical Specifications
+70
+85
5
© 2009 Micron Technology, Inc. All rights reserved.
ILmin
= –1.0V for a pulse
Unit
μA
˚C
˚C
˚C
DD
Notes
.