PIC18F6585-I/PT Microchip Technology Inc., PIC18F6585-I/PT Datasheet - Page 26

• Manufacturer Part Number: PIC18F6585-I/PT
• Description: 64 PIN, 48 KB FLASH, 3328 RAM, 52 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F6585-I/PT

• A/d Inputs: 12-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 53
• Interface: CAN/I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 48K Bytes
• Ram Size: 3.3K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F6585/8585/6680/8680
TABLE 2-2:
DS30491C-page 24
These values are for design guidance only.
See notes following this table.
20.0 MHz
32.0 kHz
200 kHz
1.0 MHz
4.0 MHz
8.0 MHz
Note 1: Higher capacitance increases the stability
Mode
HS
LP
XT
2: Rs (see Figure 2-1) may be required in
3: Since each resonator/crystal has its own
of the oscillator, but also increases the
start-up time.
HS mode, as well as XT mode, to avoid
overdriving crystals with low drive level
specifications.
characteristics, the user should consult the
resonator/crystal manufacturer for appro-
priate values of external components, or
verify oscillator performance.
20.0 MHz
25.0 MHz
Epson CA-301 20.000M-C ± 30 PPM
32.0 kHz
Epson C-001R32.768K-A
200 kHz
200 kHz
1.0 MHz
4.0 MHz
4.0 MHz
8.0 MHz
Epson CA-301 8.000M-C
STD XTL 200.000KHz
Freq
CAPACITOR SELECTION FOR
CRYSTAL OSCILLATOR
ECS ECS-10-13-1
ECS ECS-40-20-1
Ranges Tested:
Crystals Used
47-68 pF
15-33 pF
15-33 pF
33 pF
15 pF
15 pF
15 pF
15 pF
TBD
C1
± 20 PPM
± 20 PPM
± 50 PPM
± 50 PPM
± 30 PPM
47-68 pF
15-33 pF
15-33 pF
33 pF
15 pF
15 pF
15 pF
15 pF
TBD
C2
An external clock source may also be connected to the
OSC1 pin in the HS, XT and LP modes, as shown in
Figure 2-2.
FIGURE 2-2:
2.3
For timing insensitive applications, the “RC” and
“RCIO” device options offer additional cost savings.
The RC oscillator frequency is a function of the supply
voltage, the resistor (R
ues and the operating temperature. In addition to this,
the oscillator frequency will vary from unit to unit, due
to normal process parameter variation. Furthermore,
the difference in lead frame capacitance between pack-
age types will also affect the oscillation frequency,
especially for low C
take into account variation due to tolerance of external
R and C components used. Figure 2-3 shows how the
R/C combination is connected.
In the RC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic.
FIGURE 2-3:
The RCIO Oscillator mode functions like the RC mode
except that the OSC2 pin becomes an additional gen-
eral purpose I/O pin. The I/O pin becomes bit 6 of
PORTA (RA6).
C
V
Recommended values:
R
Clock from
Ext. System
EXT
SS
EXT
V
DD
RC Oscillator
Open
F
OSC
EXT
/4
EXTERNAL CLOCK INPUT
OPERATION (HS, XT OR
LP OSC CONFIGURATION)
RC OSCILLATOR MODE
OSC1
OSC2/CLKO
EXT
values. The user also needs to
 2004 Microchip Technology Inc.
3 k
C
EXT
) and capacitor (C
OSC1
OSC2
> 20pF
PIC18FXX80/XX85
R
PIC18FXX80/XX85
EXT
100 k
Internal
Clock
EXT
) val-