PIC18F6585-I/PT Microchip Technology Inc., PIC18F6585-I/PT Datasheet - Page 25

• Manufacturer Part Number: PIC18F6585-I/PT
• Description: 64 PIN, 48 KB FLASH, 3328 RAM, 52 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F6585-I/PT

• A/d Inputs: 12-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 1024 Bytes
• Input Output: 53
• Interface: CAN/I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 64-pin TQFP
• Programmable Memory: 48K Bytes
• Ram Size: 3.3K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

2.0
2.1
The PIC18F6585/8585/6680/8680 devices can be
operated in eleven different oscillator modes. The user
can program four configuration bits (FOSC3, FOSC2,
FOSC1 and FOSC0) to select one of these eleven
modes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. ECIO+PLL
11. HS+SPLL
2.2
In XT, LP, HS, HS+PLL or HS+SPLL Oscillator modes,
a crystal or ceramic resonator is connected to the OSC1
and OSC2 pins to establish oscillation. Figure 2-1
shows the pin connections.
The PIC18F6585/8585/6680/8680 oscillator design
requires the use of a parallel cut crystal.
 2004 Microchip Technology Inc.
Note:
LP
XT
HS
RC
EC
ECIO
HS+PLL
RCIO
ECIO+SPLL External Clock with software
OSCILLATOR
CONFIGURATIONS
Oscillator Types
Crystal Oscillator/Ceramic
Resonators
Use of a series cut crystal may give a fre-
quency out of the crystal manufacturers
specifications.
pin enabled
with PLL enabled
pin enabled
with software control
Low-Power Crystal
Crystal/Resonator
High-Speed Crystal/Resonator
External Resistor/Capacitor
External Clock
External Clock with I/O
High-Speed Crystal/Resonator
External Resistor/Capacitor with
I/O pin enabled
controlled PLL
External Clock with PLL and I/O
High-Speed Crystal/Resonator
PIC18F6585/8585/6680/8680
FIGURE 2-1:
TABLE 2-1:
These values are for design guidance only.
See notes following this table.
All resonators used did not have built-in capacitors.
16.0 MHz Murata Erie CSA16.00MX
2.0 MHz Murata Erie CSA2.00MG
4.0 MHz Murata Erie CSA4.00MG
8.0 MHz Murata Erie CSA8.00MT
Note 1: See Table 2-1 and Table 2-2 for recommended
Mode
Note 1: Higher capacitance increases the stability
HS
XT
C1
C2
2: A series resistor (R
3: R
2: When operating below 3V V
3: Since each resonator/crystal has its own
(1)
(1)
values of C1 and C2.
strip cut crystals.
of the oscillator, but also increases the
start-up time.
using certain ceramic resonators at any
voltage, it may be necessary to use high
gain HS mode, try a lower frequency
resonator, or switch to a crystal oscillator.
characteristics, the user should consult the
resonator/crystal manufacturer for appro-
priate values of external components, or
verify oscillator performance.
F
16.0 MHz
XTAL
R
2.0 MHz
4.0 MHz
8.0 MHz
455 kHz
varies with the oscillator mode chosen.
S
Freq
(2)
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC2
OSC1
Ranges Tested:
CRYSTAL/CERAMIC
RESONATOR OPERATION
(HS, XT OR LP
CONFIGURATION)
68-100 pF
15-68 pF
15-68 pF
10-68 pF
10-22 pF
S
) may be required for AT
R
C1
F
PIC18FXX80/XX85
(3)
DS30491C-page 23
Sleep
DD
68-100 pF
15-68 pF
15-68 pF
10-68 pF
10-22 pF
, or when
To
Internal
Logic
0.5%
0.5%
0.5%
0.5%
C2