DP83840AVCE National Semiconductor, DP83840AVCE Datasheet - Page 39

• Manufacturer Part Number: DP83840AVCE
• Description: IC ETHERNET PHYS LAYER 100-PQFP
• Manufacturer: National Semiconductor

Specifications of DP83840AVCE

• Controller Type: Ethernet Controller, 10Base-T
• Interface: IEEE 802.3af
• Voltage - Supply: 4.75 V ~ 5.25 V
• Current - Supply: 335mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-MQFP, 100-PQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *DP83840AVCE

Version A
3.0 Functional Description
3.9.6 Auto-Negotiation Complete Time
This section describes the amount of time required to
complete an Auto-Negotiation cycle for the 840A. These
times are defined for two cases. The first case assumes
that the far end link partner does not support Auto-
Negotiation and is either a fixed 10M or 100M
implementation.
Timer
break link
autoneg wait
link fail inhibit
------------------------------------------------------------------------------
Total
The second case assumes that the far end link partner fully
supports Auto-Negotiation:
Timer
break link
FLP bursts
link fail inhibit
------------------------------------------------------------------------------
Total
Refer to chapter 28 of the IEEE 802.3u standard for a full
description of the individual timers related to Auto-
Negotiation.
3.10 RESET OPERATION
The DP83840A can be reset either by hardware or
software. A hardware reset may be accomplished either by
asserting the RESET pin (pin 44) during normal operation,
or upon powering up the device. A software reset is
accomplished by setting the reset bit in the Basic Mode
Control Register (bit 15, address 00h).
While either the hardware or software reset can be
implemented at any time after device initialization,
providing a hardware reset, as described in section
3.10.1, must be implemented upon device power-up/
initialization. Omitting the hardware reset operation
during the device power-up/initialization sequence can
result in improper device operation.
3.10.1 Power-up / Reset
When V
amount of time for power to actually reach the nominal 5V
potential. This initial power-up time can be referred to as a
V
initial V
begins an internal reset operation which must be allowed
sufficient time, relative to the assertion and deassertion of
the RESET pin, to reset the device. There are two methods
for guaranteeing successful reset upon device power-up.
The first method accounts for those designs that utilize a
special power up circuit which, through hardware, will
assert the RESET pin upon power-up. In this case, the
deassertion (falling edge) of the RESET pin must not occur
until at least 500 s after the time at which the V
initially reached the 4V point.
The second method accounts for those applications which
produce a reset pulse sometime after the initial power-up
CC
ramp when V
CC
CC
ramp reaches approximately 4V, the DP83840A
is first applied to the DP83840A it takes some
Min spec
1200ms
500ms
750ms
1700-2450ms
Min spec
1200ms
104ms
750ms
1304-2054ms
CC
is “ramping” from 0V to 5V. When the
Max spec
1500ms
1000ms
1000ms
2500-3500ms
Max spec
1500ms
312ms
1000ms
1812-2812ms
(Continued)
840A
1300ms
750ms
800ms
2050-2850ms
840A
1300ms
200ms
800ms
1500-2300ms
CC
ramp
39
of the device. In this case, it is recommended that a
positive pulse, with a duration of at least 1 s, be applied to
the RESET pin no sooner than 500 s after the point in time
where the initial V
In both methods described above, it is important to note
that the logic levels present at each of the hardware
configuration pins of the DP83840A (see list below) are
also latched into the device as a function of the reset
operation (either hardware or software). These hardware
configuration values are guaranteed to be latched into the
DP83840A 2 s after the deassertion of the RESET pin.
The hardware configuration values latched into the
DP83840A during the reset operation are dependent on
the logic levels present at the following device pins upon
power-up:
During the power-up reset operation the LED1 through
LED5 pins are undefined, the SPEED_10 pin will be
asserted, and the SPEED_100 pin will be deasserted.
3.10.2 Hardware Reset
A hardware Reset is accomplished by applying a positive
pulse, with a duration of at least 1 s, to the RESET pin of
the DP83840A during normal operation. This will reset the
device such that all registers will be reset to default values
and the hardware configuration values will be re-latched
into the device (similar to the power-up reset operation).
3.10.3 Software Reset
A software reset is accomplished by setting bit 15 of the
Basic Mode Control Register (address 00h). This bit is self
clearing and, when set, will return a value of “1” until the
software reset operation has completed. The software
reset will reset the device such that all registers will be
reset to default values and the hardware configuration
values will be re-latched into the device (similar to the
power-up reset operation). Driver code should wait 500 s
following a software reset before allowing further serial MII
operations with the DP83840A.
Pin #
49
53
66
89
63
95
46
47
98
99
100
1
Primary Function
LBEN
ENCSEL
CRS
PHYAD[3]
RX_ER
AN0
AN1
REPEATER
10BTSER
BPALIGN
BP4B5B
BPSCR
National Semiconductor
CC
ramp reached 4V.
Latched in at Reset
PHYAD[0]
PHYAD[1]
PHYAD[2]
PHYAD[3]
PHYAD[4]
AN0
AN1
REPEATER
10BTSER
BPALIGN
BP4B5B
BPSCR