ST72F324BK6TAS STMicroelectronics, ST72F324BK6TAS Datasheet - Page 121
ST72F324BK6TAS
Manufacturer Part Number
ST72F324BK6TAS
Description
8-BIT MCU
Manufacturer
STMicroelectronics
Datasheet
1.ST72F324BK6TAS.pdf
(198 pages)
- Current page: 121 of 198
- Download datasheet (3Mb)
ST72324B-Auto
Clock deviation causes
The causes which contribute to the total deviation are:
●
●
●
●
All the deviations of the system should be added and compared to the SCI clock tolerance:
Noise error causes
See also the description of Noise error in
Start bit
The Noise Flag (NF) is set during start bit reception if one of the following conditions occurs:
1.
2.
Therefore, a valid Start bit must satisfy both the above conditions to prevent the Noise Flag
from being set.
Data bits
The Noise Flag (NF) is set during normal data bit reception if the following condition occurs:
During the sampling of 16 samples, if all three samples numbered 8, 9 and10 are not the
same. The majority of the 8th, 9th and 10th samples is considered as the bit value.
Therefore, a valid Data bit must have samples 8, 9 and 10 at the same value to prevent the
Noise Flag from being set.
Figure 58. Bit sampling in Reception mode
D
transmitter is transmitting at a different baud rate).
D
D
the reception of one complete SCI message assuming that the deviation has been
compensated at the beginning of the message.
D
A valid falling edge is not detected. A falling edge is considered to be valid if the three
consecutive samples before the falling edge occurs are detected as ‘1’ and, after the
falling edge occurs, during the sampling of the 16 samples, if one of the samples
numbered 3, 5 or 7 is detected as a ‘1’.
During sampling of the 16 samples, if one of the samples numbered 8, 9 or 10 is
detected as a ‘1’.
Sample
clock
TRA
QUANT
REC
TCL
RDI line
: Deviation due to the transmission line (generally due to the transceivers)
: Deviation due to transmitter error (local oscillator error of the transmitter or the
: Deviation of the local oscillator of the receiver: This deviation can occur during
: Error due to the baud rate quantization of the receiver.
1
2
D
3
TRA
Doc ID13466 Rev 4
4
+ D
7/16
QUANT
5
6
Receiver on page
+ D
7
sampled values
REC
One bit time
8
+ D
9
TCL
10
< 3.75%
11
115.
12
6/16
7/16
13
On-chip peripherals
14
15
16
121/198
Related parts for ST72F324BK6TAS
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: