72T7285L4-4BB IDT, Integrated Device Technology Inc, 72T7285L4-4BB Datasheet - Page 31
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
72T7285L4-4BB
Manufacturer Part Number
72T7285L4-4BB
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.72T7285L4-4BB.pdf
(53 pages)
Specifications of 72T7285L4-4BB
Configuration
Dual
Density
1.125Mb
Access Time (max)
3.4ns
Word Size
72b
Organization
16Kx72
Sync/async
Synchronous
Expandable
Yes
Bus Direction
Uni-Directional
Package Type
BGA
Clock Freq (max)
225MHz
Operating Supply Voltage (typ)
2.5V
Operating Supply Voltage (min)
2.375V
Operating Supply Voltage (max)
2.625V
Supply Current
130mA
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
324
Lead Free Status / Rohs Status
Not Compliant
THE INSTRUCTION REGISTER
processor at the rising edge of TCLK.
register to be accessed, or both. The instruction shifted into the register is latched
at the completion of the shifting process when the TAP controller is at Update-
IR state.
which can hold instruction data. These mandatory cells are located nearest the
serial outputs they are the least significant bits.
TEST DATA REGISTER
Boundary Scan register and Device ID register.
and a common serial data output.
complete description, refer to the IEEE Standard Test Access Port Specification
(IEEE Std. 1149.1-1990).
TEST BYPASS REGISTER
to TDO. It contains a single stage shift register for a minimum length in serial path.
When the bypass register is selected by an instruction, the shift register stage
is set to a logic zero on the rising edge of TCLK when the TAP controller is in
the Capture-DR state.
operation of the device in response to the BYPASS instruction.
THE BOUNDARY-SCAN REGISTER
out of the processor input/output ports. The Boundary Scan Register is a part
of the IEEE 1149.1-1990 Standard JTAG Implementation.
THE DEVICE IDENTIFICATION REGISTER
specify the manufacturer, part number and version of the processor to be
determined through the TAP in response to the IDCODE instruction.
is dropped in the 11-bit Manufacturer ID field.
field contains the following values:
16,384 x 72, 32,768 x 72, 65,536 x 72, 131,072 x 72
31(MSB)
Version (4 bits)
0X0
The Instruction register allows an instruction to be shifted in serially into the
The Instruction is used to select the test to be performed, or the test data
The instruction register must contain 4 bit instruction register-based cells
The Test Data register contains three test data registers: the Bypass, the
These registers are connected in parallel between a common serial input
The following sections provide a brief description of each element. For a
The register is used to allow test data to flow through the device from TDI
The operation of the bypass register should not have any effect on the
The Boundary Scan Register allows serial data TDI be loaded in to or read
The Device Identification Register is a Read Only 32-bit register used to
IDT JEDEC ID number is 0xB3. This translates to 0x33 when the parity
For the IDT72T7285/72T7295/72T72105/72T72115, the Part Number
IDT72T7285/95/105/115 JTAG Device Identification Register
28 27
Part Number (16-bit) Manufacturer ID (11-bit)
IDT72T72105
IDT72T72115
IDT72T7285
IDT72T7295
Device
12 11
Part# Field
0X33
0493
0492
0491
0490
1 0(LSB)
1
31
JTAG INSTRUCTION REGISTER
when the TAP controller is in the Shift-IR state. The instruction is decoded to
perform the following:
16 different possible instructions. Instructions are decoded as follows.
a complete description refer to the IEEE Standard Test Access Port Specification
(IEEE Std. 1149.1-1990).
EXTEST
test mode and selects the boundary-scan register to be connected between TDI
and TDO. During this instruction, the boundary-scan register is accessed to
drive test data off-chip via the boundary outputs and receive test data off-chip
via the boundary inputs. As such, the EXTEST instruction is the workhorse of
IEEE. Std 1149.1, providing for probe-less testing of solder-joint opens/shorts
and of logic cluster function.
IDCODE
and selects the optional device identification register to be connected between
TDI and TDO. The device identification register is a 32-bit shift register containing
information regarding the IC manufacturer, device type, and version code.
Accessing the device identification register does not interfere with the operation
of the IC. Also, access to the device identification register should be immediately
available, via a TAP data-scan operation, after power-up of the IC or after the
TAP has been reset using the optional TRST pin or by otherwise moving to the
Test-Logic-Reset state.
SAMPLE/PRELOAD
normal functional mode and selects the boundary-scan register to be connected
between TDI and TDO. During this instruction, the boundary-scan register can
be accessed via a date scan operation, to take a sample of the functional data
entering and leaving the IC. This instruction is also used to preload test data into
the boundary-scan register before loading an EXTEST instruction.
HIGH-IMPEDANCE
as well as three-state types) of an IC to a disabled (high-impedance) state and
selects the one-bit bypass register to be connected between TDI and TDO.
During this instruction, data can be shifted through the bypass register from TDI
to TDO without affecting the condition of the IC outputs.
BYPASS
functional mode and selects the one-bit bypass register to be connected between
TDI and TDO. The BYPASS instruction allows serial data to be transferred
through the IC from TDI to TDO without affecting the operation of the IC.
Hex Value Instruction
0x00
0x02
0x01
0x03
0x0F
•
•
The required EXTEST instruction places the IC into an external boundary-
The optional IDCODE instruction allows the IC to remain in its functional mode
The required SAMPLE/PRELOAD instruction allows the IC to remain in a
The optional High-Impedance instruction sets all outputs (including two-state
The required BYPASS instruction allows the IC to remain in a normal
Select test data registers that may operate while the instruction is current.
The other test data registers should not interfere with chip operation and the
selected data register.
Define the serial test data register path that is used to shift data between
TDI and TDO during data register scanning.
The Instruction register allows instruction to be serially input into the device
The Instruction Register is a 4 bit field (i.e. IR3, IR2, IR1, IR0) to decode
The following sections provide a brief description of each instruction. For
EXTEST
IDCODE
SAMPLE/PRELOAD Select Boundary Scan Register
HIGH-IMPEDANCE JTAG
BYPASS
JTAG Instruction Register Decoding
COMMERCIAL AND INDUSTRIAL
Select Chip Identification data register
Function
Select Boundary Scan Register
Select Bypass Register
TEMPERATURE RANGES