5535032-5 TE Connectivity, 5535032-5 Datasheet - Page 17

• Manufacturer Part Number: 5535032-5
• Description: ASSY,RECEPTACLE,EUROCARD,TYPE C,LEAD-FRE
• Manufacturer: TE Connectivity
• Series: 5535032 Seriesr
• Type: Type Cr

Specifications of 5535032-5

• Pitch Spacing: 2.54mm
• No. Of Contacts: 96
• Gender: Receptacle
• No. Of Rows: 3
• Rows Loaded: A + B + C
• Contact Termination: Through Hole
• Contact Material: Brass
• Contact Plating: Gold
• Approval: RoHS Compliant
• Number Of Rows: 3
• Number Of Positions / Contacts: 96
• Termination Style: Solder Pin
• Pitch: 2.54 mm
• Connector Type: Connector Assembly
• Pcb Mount Retention: With
• Pcb Mounting Orientation: Vertical
• Pcb Thickness (minimum) (mm [in]): 1.57 [0.062]
• Post Type: Compliant Post
• Size: Standard
• Make First / Break Last: No
• Bus Type: FUTUREBUS, MULTIBUS (II), NUBUS, VMEbus, VXIBus
• Din Level: II
• Mounting Ears: With
• Toolless (flat Rock): Yes
• Termination Post Length (mm [in]): 4.83 [0.190]
• Solder Tail Contact Plating: Tin
• Centerline (mm [in]): 2.54 [0.100]
• Number Of Positions: 96
• Pcb Mount Retention Type: Compliant Posts
• Contact Cross Section (mm [in]): 0.30 x 0.61 [.012 x .024]
• Contact Type: Socket
• Contact Base Material: Copper Alloy
• Contact Plating, Mating Area, Material: DIN 41612 Class 2
• Connector Style: Receptacle
• Housing Material: Polymer
• Ul Flammability Rating: UL 94V-0
• Flux-tight Coating: Without
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Applies To: Printed Circuit Board
• High Temperature Housing: No
• Lead Free Status / Rohs Status: Details

5.5. Connector Replacement Tooling
When entire Type C receptacle connectors and Type R pin connectors must be replaced, Eurocard Connector
Removal Tool Kit 534611--1 should be used. Refer to Figure 16 and proceed as follows:
5.6. Contact Extraction Tooling
Extraction tooling is available for withdrawal of individual power contacts and coaxial contacts from Type M
connectors. The tip of the tool is inserted into the contact cavity from the mating side of the housing. The
contact is forced out of the rear of the housing by pushing the tool handle. See Figure 16.
Rev G
CAUTION
Support Block
!
1. Place support block with slot up on the arbor frame support base.
2. Place housing down on support block with pins extending up through pc board.
3. Slide guide block over wire--wrap tails. Be sure the “T” stamp on end of guide block is away from pc
board.
4. Start push--out assembly into guide block, using care not to damage pins.
5. Lower the arbor ram onto the center of push--out assembly and apply force until it is seated on guide
block.
6. Raise the arbor ram and remove push--out assembly and guide block. When the board, the
connector, and the support block are removed, the connector will fall away with pins removed from the
pc board and housing.
Guide Block
Push- - Out
Assembly
“T” Stamp
Slot
DO NOT use this tool in a power assist unit. This procedure should be done with a manually operated unit only.
Ram
Figure 16
Pins
PC Board
Connector
Extraction Tool
106242- - 1
114- 9014
17 of 18