ISP1504CBS,157 NXP Semiconductors, ISP1504CBS,157 Datasheet - Page 32
![RF Transceiver USB2.0 ULPI OTG](/photos/15/65/156561/hvqfn32_sml.jpg)
ISP1504CBS,157
Manufacturer Part Number
ISP1504CBS,157
Description
RF Transceiver USB2.0 ULPI OTG
Manufacturer
NXP Semiconductors
Datasheet
1.ISP1504ABS118.pdf
(83 pages)
Specifications of ISP1504CBS,157
Number Of Transceivers
1
Esd Protection
YeskV
Operating Supply Voltage (typ)
Not RequiredV
Operating Temperature Classification
Industrial
Operating Supply Voltage (max)
Not RequiredV
Operating Supply Voltage (min)
Not RequiredV
Pin Count
32
Mounting
Surface Mount
Operating Temperature (max)
85C
Operating Temperature (min)
-40C
Operating Supply Voltage
1.65 V to 3.6 V
Mounting Style
SMD/SMT
Package / Case
HVQFN-32
Lead Free Status / RoHS Status
Compliant
Other names
935278309157 ISP1504CBS
NXP Semiconductors
ISP1504A_ISP1504C_3
Product data sheet
Fig 12. Example of register write, register read, extended register write and extended register read
DATA[7:0]
CLOCK
NXT
STP
DIR
AD indicates the address byte, and D indicates the data byte.
9.6 Register read and write operations
9.7 USB reset and high-speed detection handshake (chirp)
(REGW)
register write
TXCMD
immediate
Figure 12
addressing and extended addressing register operations. Extended register addressing is
optional for links. Note that register operations will be aborted if the ISP1504 unexpectedly
asserts DIR during the operation. When a register operation is aborted, the link must retry
until successful. For more information on register operations, refer to UTMI+ Low Pin
Interface (ULPI) Specification Rev. 1.1 .
Figure 13
handshake (chirp). The sequence is shown for hosts and peripherals.
show all RXCMD updates, and timing is not to scale. The sequence is as follows:
1. USB reset: The host detects a peripheral attachment as low-speed if DM is HIGH and
2. High-speed detection handshake (chirp)
D
as full-speed if DP is HIGH. If a host detects a low-speed peripheral, it does not follow
the remainder of this protocol. If a host detects a full-speed peripheral, it resets the
peripheral by writing to the Function Control register. XCVRSELECT[1:0] = 00b
(high-speed) and TERMSELECT = 0b are then set which drives SE0 on the bus (DP
and DM connected to ground through 45 ). The host also sets OPMODE[1:0] = 10b
for correct chirp transmit and receive. The start of SE0 is labeled T
Remark: To receive chirp signaling, the host must also consider the high-speed
differential receiver output. The host controller must interpret LINESTATE[1:0] as
shown in
a. Peripheral chirp: After detecting SE0 for no less than 2.5 s, if the peripheral is
capable of high-speed, it sets XCVRSELECT[1:0] = 00b (high-speed) and
OPMODE[1:0] = 10b (chirp). The peripheral immediately follows this with a
TXCMD (NOPID), transmitting a Chirp K for no less than 1 ms and ending no more
shows register read and write sequences. The ISP1504 supports immediate
shows the sequence of events for USB reset and high-speed detection
TXCMD
(EXTW) AD D
register write
Table
extended
13.
Rev. 03 — 7 April 2008
TXCMD
(REGR)
register read
immediate
D
ISP1504A; ISP1504C
TXCMD
(EXTW)
register read
extended
AD
ULPI HS USB OTG transceiver
D
Figure 13
0
© NXP B.V. 2008. All rights reserved.
.
004aaa710
does not
31 of 82