PIC24HJ32GP202-E/MM Microchip Technology, PIC24HJ32GP202-E/MM Datasheet - Page 203

• Manufacturer Part Number: PIC24HJ32GP202-E/MM
• Description: 16-bit MCU, 32KB Flash,40 MIPS,nanoWatt 28 QFN-S 6x6mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ32GP202-E/MM

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 32KB (11K x 24)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

FIGURE 22-2:
TABLE 22-16: EXTERNAL CLOCK TIMING REQUIREMENTS
© 2011 Microchip Technology Inc.
AC CHARACTERISTICS
OS10
OS20
OS25
OS30
OS31
OS40
OS41
OS42
Note 1:
Param
No.
OSC1
CLKO
2:
3:
4:
5:
6:
PIC24HJ32GP202/204 AND PIC24HJ16GP304
F
T
T
TosL,
TosH
TosR,
TosF
TckR
TckF
G
Symb
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
Instruction cycle period (T
are based on characterization data for that particular oscillator type under standard operating conditions
with the device executing code. Exceeding these specified limits can result in an unstable oscillator
operation and/or higher than expected current consumption. All devices are tested to operate at “min.”
values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the
“max.” cycle time limit is “DC” (no clock) for all devices.
Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin.
These parameters are characterized by similarity, but are tested in manufacturing at F
These parameters are characterized by similarity, but are not tested in manufacturing.
Data for this parameter is preliminary. This parameter is characterized, but is not tested in manufacturing.
OSC
CY
IN
M
External CLKI Frequency
(External clocks allowed only
in EC and ECPLL modes)
Oscillator Crystal Frequency
T
Instruction Cycle Time
External Clock in (OSC1)
High or Low Time
External Clock in (OSC1)
Rise or Fall Time
CLKO Rise Time
CLKO Fall Time
External Oscillator
Transconductance
OSC
EXTERNAL CLOCK TIMING
= 1/F
OS41
Characteristic
OSC
(4)
(3,5)
Q1
(3,5)
CY
(6)
OS20
) equals two times the input oscillator time-base period. All specified values
(2,4)
Q2
(5)
(5)
(4)
OS25
(5)
Q3
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature
0.375 x T
OS40
12.5
Min
DC
3.5
Q4
10
25
14
—
—
—
OSC
OS30
Q1
Typ
5.2
5.2
16
—
—
—
—
—
—
—
—
OS30
(1)
Q2
0.625 x T
-40°C ≤ T
-40°C ≤ T
Q3
Max
DC
DC
40
10
40
33
20
18
—
—
OS31
OSC
A
A
Q4
≤ +125°C for Extended
≤ +85°C for Industrial
OS31
Units
mA/V V
MHz
MHz
MHz
kHz
ns
ns
ns
ns
ns
ns
IN
DS70289G-page 203
= 40 MHz only.
EC
XT
HS
SOSC
EC
EC
T
A
DD
Conditions
= +25ºC
= 3.3V
—
—
—
—