82V2042EPF8 IDT, Integrated Device Technology Inc, 82V2042EPF8 Datasheet - Page 11
![](/photos/31/30/313074/80pin_tqfp_sml.jpg)
82V2042EPF8
Manufacturer Part Number
82V2042EPF8
Description
Manufacturer
IDT, Integrated Device Technology Inc
Datasheet
1.82V2042EPF8.pdf
(83 pages)
Specifications of 82V2042EPF8
Screening Level
Industrial
Mounting
Surface Mount
Package Type
TQFP
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Lead Free Status / RoHS Status
Not Compliant
Table-1 Pin Description (Continued)
PIN DESCRIPTION
IDT82V2042E
RD1/RDP1
RD2/RDP2
CV1/RDN1
CV2/RDN2
RCLK1
RCLK2
MCLK
Name
LOS1
LOS2
REF
Type
O
O
O
I
I
Pin No.
34
26
33
27
35
25
30
32
28
71
RDn: Receive Data output for Channel 1~2
In single rail mode, this pin outputs NRZ data. The data is decoded according to AMI, HDB3 or B8ZS line code rules.
CVn: Code Violation indication
In single rail mode, the BPV/CV errors in received data stream will be reported by driving the CVn pin to high level for a full
clock cycle. B8ZS/HDB3 line code violation can be indicated if the B8ZS/HDB3 decoder is enabled. When AMI decoder is
selected, bipolar violation will be indicated.
In hardware control mode, the EXZ, BPV/CV errors in received data stream are always monitored by the CVn pin if single rail
mode is chosen.
RDPn/RDNn: Positive/Negative Receive Data output for Channel 1~2
In dual rail mode, these pins output the re-timed NRZ data when CDR is enabled, or directly outputs the raw RZ slicer data
if CDR is bypassed.
Active edge and level select:
Data on RDPn/RDNn or RDn is clocked with either the rising or the falling edge of RCLKn. The active polarity is also select-
able. Refer to
RCLKn: Receive Clock output for Channel 1~2
This pin outputs 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode receive clock. Under LOS conditions with AIS enabled
(bit AISE=1), RCLKn is derived from MCLK.
In clock recovery mode, this signal provides the clock recovered from the RTIPn/RRINGn signal. The receive data (RDn in
single rail mode or RDPn and RDNn in dual rail mode) is clocked out of the device on the active edge of RCLKn.
If clock recovery is bypassed, RCLKn is the exclusive OR (XOR) output of the dual rail slicer data RDPn and RDNn. This signal
can be used in applications with external clock recovery circuitry.
MCLK: Master Clock input
A built-in clock system that accepts selectable 2.048 MHz reference for E1 operating mode and 1.544 MHz reference for T1/
J1 operating mode. This reference clock is used to generate several internal reference signals:
•
•
•
•
•
•
The loss of MCLK will turn TTIP/TRING into high impedance status.
LOSn: Loss of Signal Output for Channel 1~2
These pins are used to indicate the loss of received signals. When LOSn pin becomes high, it indicates the loss of received
signal in channel n. The LOS pin will become low automatically when valid received signal is detected again. The criteria of
loss of signal are described in
REF: reference resister
An external resistor (3kΩ, 1%) is used to connect this pin to ground to provide a standard reference current for internal circuit.
Timing reference for the integrated clock recovery unit.
Timing reference for the integrated digital jitter attenuator.
Timing reference for microcontroller interface.
Generation of RCLKn signal during a loss of signal condition.
Reference clock to transmit All Ones, all zeros, PRBS/QRSS pattern as well as activate or deactivate Inband Loop-
back code if MCLK is selected as the reference clock. Note that for ATAO and AIS, MCLK is always used as the refer-
ence clock.
Reference clock during Transmit All Ones (TAO) condition or sending PRBS/QRSS in hardware control mode.
3.4.8 RECEIVE PATH SYSTEM INTERFACE
3.6 LOS AND AIS
DUAL CHANNEL T1/E1/J1 SHORT HAUL LINE INTERFACE UNIT
11
DETECTION.
Description
for details.
December 12, 2005