600880 Tyco Electronics, 600880 Datasheet - Page 22

• Manufacturer Part Number: 600880
• Description: Connector Accessories Hand Tool Left Die Set
• Manufacturer: Tyco Electronics
• Type: Die Setr

22
Product Facts
Applications
Terminates all magnet wire
film insulations
Eliminates need for pre-
stripping conductors
Eliminates need to post
insulate termination
Excess magnet wire is
automatically trimmed
during the termination
process
Series 187 and 250 Tab
terminals available
Terminates 33-17 AWG
[0.18-1.15 mm] magnet wire
Simultaneously terminates
two magnet wires of the
same size in one terminal
from 33-23 AWG [0.18-
0.57 mm]
Available in strip form for
semi-automatic or fully
automatic insertions
Available in loose piece
form for hand tool insertions
Varnish resist tab terminals
are available for special
applications
High speed, fully automated
integrated systems provide
uniform terminations
reliability at the lowest
possible applied cost
Clean metal-to-metal
interface produces stable,
gas-tight electrical
terminations free of oxides
and other contaminants
Recognized under the
Component Recognition
Program of Underwriters
Laboratories Inc.,
File No. E13288
Motor windings and
connections
Coil Connections
Transformer windings and
connections
Bobbin connections
Lighting Ballasts
Power Supplies
R
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Magnet Wire Terminals and Termination Systems
Magnet Wire Terminals and Termination Systems
Slim Line MAG-MATE Terminals
Tyco Electronics offers a full
selection of Series 187 and
250 Slim Line MAG-MATE
Tab insulation displacement
(IDC) terminals for magnet
wire terminations.
Slim Line MAG-MATE
Series 187 and 250 tab
terminals with a single IDC
slot terminate 33-17 AWG
[0.18 to 1.15 mm].
Each IDC slot terminates up
to four consecutive magnet
wire ranges.
Two magnet wires with the
same diameter can be
terminated in one terminal
down to 23 AWG [0.57 mm].
According to Tyco Electronics
specifications MAG-MATE
cavities are either
integrated into coil bodies
or especially designed
cavity housings.The magnet
wires are precisely
positioned in the “U” shaped
designed termination slots.
The MAG-MATE Inserter
cuts the terminals from the
strip and places the
terminals over the magnet
wire into the plastic cavities.
Dimensions are shown for
reference purposes only.
Specifications subject to change.
During this operation the
small stripping devices
penetrate the film insulation
from the magnet wire.
Residual spring energy in
the terminal causes the side
walls of each IDC slot to
function as opposing
cantilever beams.
This constant pressure
results in an intimate metal-
to-metal interface, providing
a reliable, long-term
connection.
The wiping action between
the wire and terminals
removes oxides or other
contaminants present on
both the conductor and the
terminal slot side walls,
producing a clean, stable,
gas-tight electrical
termination.
The AMP MAG-MATE
Inserter may be used as a
semi-automatic bench
machine or integrated in
production lines for fully-
automatic applications.
Technical Support
USA: 1-800-522-6752
Canada: 1-905-475-6222
Mexico: 01-800-733-8926
Typical Plastic Cavity
Not for design, Tyco Electronics will
supply required dimensions of cavity
for each customer application.
Technical Documents
Application Specifications
describe requirements for using
the product in its intended
application and or crimping
information. They are intended
for the Packaging and Design
Engineer and the Machine
Setup Person.
114-2140—Slim Line
Reference Application
[6.86]
.270
Spec. 114-2147
Min.
www.tycoelectronics.com
MAG-MATE
Terminals
Catalog 82221
Revised 10-02
[2.92]
.115
[9.53]
.375
Min.
Min.