600880 Tyco Electronics, 600880 Datasheet - Page 2

• Manufacturer Part Number: 600880
• Description: Connector Accessories Hand Tool Left Die Set
• Manufacturer: Tyco Electronics
• Type: Die Setr

2
Typical Plastic Cavities
Manufacture only according
to Tyco Electronics
Specification.
Technical Documents
Application Specifications
describe requirements for using
the product in its intended
application and or crimping
information. They are intended
for the Packaging and Design
Engineer and the Machine
Setup Person.
114-2050—Poke-In Tab
114-2069—Standard
114-2046—Standard
114-2066—Standard
114-2067—Standard
114-2094—Standard
MAG-MATE
Terminals
MAG-MATE .187
[4.75] Box Height
Terminals
MAG-MATE .300
[7.62] Box Height
Terminals
MAG-MATE .500
[12.7] Box Height
Terminals
MAG-MATE .300
[7.62] Box Height
Latch-In Terminals
Narrow Body
MAG-MATE .300
[7.62] Box Height
Latch-In Terminals
Wide Body
Dimensions are in inches and
millimeters unless otherwise
specified. Values in brackets
are metric equivalents.
Magnet Wire Terminals and Termination Systems
Standard MAG-MATE Terminals
Note: MAG-MATE typical
plastic cavities are not for
design; Tyco Electronics
will supply required
dimensions of cavity for
each customer application.
Plastic cavities, designed
to Tyco Electronics
specifications, may be
molded as part of the coil
bobbin or attached to a
lamination stack in the area
of the magnet wire coil.
Each cavity is a rectangular
box with two narrow slots
on opposing walls and a
plastic post or anvil
extending upward from the
bottom surface.
During or after the winding
process, the magnet wire is
placed across the plastic
cavities and into the slots,
.187 [4.75] Box Height MAG-MATE
.500 [12.70] Box Height
(Reference Application
(Reference Application
Spec. 114-2069)
Spec. 114-2066)
Cavity Size 1,
Cavity Size 4,
MAG-MATE
Dimensions are shown for
reference purposes only.
Specifications subject to change.
either manually or by coil
winding equipment.
Unraveling is prevented by
a slight friction fit, suitable
bend or by wrapping the
magnet wire around a tie-off
post.
During insertion, two
insulation displacing
terminal slots strip the film
insulation from the magnet
wire producing a stable
electrical termination.
The plastic anvil supports
the magnet wire, helping to
prevent it from being
dragged down when the
terminal is inserted.
Terminal retention is
secured in the plastic
cavities by either locking
barbs or locking latches in
addition to locking barbs for
.300 [7.62] Box Height MAG-MATE
Latch-In MAG-MATE, Narrow
[ 5.46 ] Min.
(Reference Application
(Reference Application
.215
.300 [7.62] Box Height
(Continued)
Spec. 114-2046)
Spec. 114-2067)
Cavity Size 2,
Cavity Size 5,
Body
[ 5.97 ] Min.
.235
Technical Support
USA: 1-800-522-6752
Canada: 1-905-475-6222
Mexico: 01-800-733-8926
[ 9.08 ] Min.
.355
quick disconnect FASTON
tab terminals.
Excess magnet wire is
trimmed flush with the
outside of the plastic cavity
by a shear blade traveling
with the terminal insertion
ram.
The sheared wire end can
be tucked inside the plastic
cavity, if necessary, by
cutting the wire off before
the terminal is fully seated
allowing the terminal to drag
the severed end of the wire
into the pocket inside the
cavity.
Tyco Electronics will
provide design and mold
engineering resources to
manufacture any
specifically designed
MAG-MATE cavity
housing.
Latch-In MAG-MATE, Wide Body
(Reference Application
(Reference Application
.300 [7.62] Box Height
.300 [7.62] Box Height
Spec. 114-2094)
Spec. 114-2046)
Cavity Size 3,
Cavity Size 6,
www.tycoelectronics.com
MAG-MATE
Catalog 82221
Revised 10-02