ADSP-21369KSWZ-1A Analog Devices Inc, ADSP-21369KSWZ-1A Datasheet - Page 19

• Manufacturer Part Number: ADSP-21369KSWZ-1A
• Description: 266 MHz, Shared Memory,S/PDIF EPAD PBfr
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Floating Pointr

Specifications of ADSP-21369KSWZ-1A

• Interface: DAI, DPI
• Clock Rate: 266MHz
• Non-volatile Memory: ROM (768 kB)
• On-chip Ram: 256kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 208-LQFP
• Device Core Size: 32/40Bit
• Architecture: Super Harvard
• Format: Floating Point
• Clock Freq (max): 266MHz
• Mips: 266
• Device Input Clock Speed: 266MHz
• Ram Size: 256KB
• Program Memory Size: 768KB
• Operating Supply Voltage (typ): 1.2/3.3V
• Operating Supply Voltage (min): 1.14/3.13V
• Operating Supply Voltage (max): 1.26/3.47V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: LQFP EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ADZS-21369-EZLITE - KIT EVAL EZ LITE ADDS-21369
• Lead Free Status / Rohs Status: Compliant

The VCO frequency is calculated as follows:
f
f
where:
f
PLLM = Multiplier value programmed in the PMCTL register.
During reset, the PLLM value is derived from the ratio selected
using the CLK_CFG pins in hardware.
PLLD = Divider value 1, 2, 4, or 8 based on the PLLD value pro-
grammed on the PMCTL register. During reset this value is 1.
f
f
f
VCO
CCLK
VCO
INPUT
INPUT
INPUT
• The product of CLKIN and PLLM must never exceed f
= 2 PLLM f
= VCO output
(max) in
(INDIV = 1).
= (2 PLLM f
XTAL
= Input frequency to the PLL.
= CLKIN when the input divider is disabled or
= CLKIN 2 when the input divider is enabled
BUF
CLKIN
Table 13
4096 CLKIN
DELAY OF
CYCLES
INPUT
INPUT
if the input divider is enabled
DIVIDER
CLKIN
PMCTL
(INDIV)
) (2 PLLD)
f
INPUT
Figure 5. Core Clock and System Clock Relationship to CLKIN
CLK_CFGx/PMCTL (2xPLLM)
FILTER
LOOP
MULTIPLIER
CLKOUT (TEST ONLY)
PLL
Rev. E | Page 19 of 60 | July 2009
PLL
VCO
VCO
f
VCO
DIVIDER
(2xPLLD)
PMCTL
PLL
ADSP-21367/ADSP-21368/ADSP-21369
Note the definitions of the clock periods that are a function of
CLKIN and the appropriate ratio control shown in and
Table
peripherals are defined in relation to t
cific timing section for each peripheral’s timing information.
Table 11. Clock Periods
Figure 5
lator or crystal. The shaded divider/multiplier blocks denote
where clock ratios can be set through hardware or software
using the power management control register (PMCTL). For
more information, see the processor hardware reference.
Timing
Requirements
t
t
t
CK
CCLK
PCLK
f
CCLK
11. All of the timing specifications for the ADSP-2136x
(PLLBP)
PMCTL
shows core to CLKIN relationships with external oscil-
CCLK
(SDCKR)
DIVIDER
Description
CLKIN Clock Period
Processor Core Clock Period
Peripheral Clock Period = 2 × t
SDRAM
PMCTL
DIVIDE
BY 2
BUF
PCLK
PCLK
(PLLBP)
PMCTL
. See the peripheral spe-
PCLK
CCLK
SDCLK
CCLK