LPC2292FBD144 NXP Semiconductors, LPC2292FBD144 Datasheet - Page 32

• Manufacturer Part Number: LPC2292FBD144
• Description: 16/32BIT ARM7 MCU, 256K FLASH, 144LQFP
• Manufacturer: NXP Semiconductors

Specifications of LPC2292FBD144

• No. Of I/o's: 112
• Ram Memory Size: 16KB
• Cpu Speed: 60MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 6
• Digital Ic Case: RoHS Compliant
• Core Size: 32bit
• Program Memory Size: 256KB
• Oscillator Type: External Only
• Controller Family/series: LPC22xx
• Rohs Compliant: Yes

NXP Semiconductors
Table 7.
T
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] Applies to P1[25:16].
[11] See the LPC2119/2129/2194/2292/2294 User Manual .
[12] To V
Table 8.
V
[1]
[2]
[3]
[4]
[5]
[6]
[7]
LPC2292_2294_7
Product data sheet
Symbol
Oscillator pins
V
V
Symbol
V
C
E
E
E
E
E
amb
DDA
i(XTAL1)
o(XTAL2)
IA
D
L(adj)
O
G
T
ia
Typical ratings are not guaranteed. The values listed are at room temperature (+25 C), nominal supply voltages.
Internal rail.
External rail.
Including voltage on outputs in 3-state mode.
V
3-state outputs go into 3-state mode when V
Accounts for 100 mV voltage drop in all supply lines.
Allowed as long as the current limit does not exceed the maximum current allowed by the device.
Minimum condition for V
Conditions: V
The ADC is monotonic, there are no missing codes.
The differential linearity error (E
The integral non-linearity (E
appropriate adjustment of gain and offset errors. See
The offset error (E
ideal curve. See
The gain error (E
error, and the straight line which fits the ideal transfer curve. See
The absolute voltage error (E
non-calibrated ADC and the ideal transfer curve. See
= 40 C to +125 C, unless otherwise specified.
= 2.5 V to 3.6 V; T
DD(3V3)
SS
.
Parameter
input voltage on pin XTAL1
output voltage on pin
XTAL2
Static characteristics
ADC static characteristics
supply voltages must be present.
Parameter
analog input voltage
analog input
capacitance
differential linearity
error
integral non-linearity
offset error
gain error
absolute error
SSA
Figure
G
= 0 V, V
O
) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
amb
5.
I
= 4.5 V, maximum condition for V
DDA
= 40 C to +125 C unless otherwise specified. ADC frequency 4.5 MHz.
L(adj)
T
= 3.3 V.
) is the maximum difference between the center of the steps of the actual transfer curve of the
D
) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
) is the difference between the actual step width and the ideal step width. See
…continued
Conditions
Conditions
DD(3V3)
Rev. 7 — 4 December 2008
16/32-bit ARM microcontrollers with external memory interface
is grounded.
Figure
Figure
I
= 5.5 V.
5.
5.
Figure
5.
[1][2][3]
[1][4]
[1][5]
[1][6]
[1][7]
Min
0
-
-
-
-
-
-
Min
0
0
LPC2292/LPC2294
Typ
-
-
-
-
-
-
-
Typ
-
-
[1]
Max
V
1
Figure
© NXP B.V. 2008. All rights reserved.
1
2
3
0.5
4
DDA
Max
1.8
1.8
5.
Unit
V
pF
LSB
LSB
LSB
%
LSB
32 of 53
Unit
V
V