DSPIC30F5011-30I/PTG Microchip Technology, DSPIC30F5011-30I/PTG Datasheet - Page 167

• Manufacturer Part Number: DSPIC30F5011-30I/PTG
• Description: 16BIT MCU-DSP 30MHZ, SMD, 30F5011
• Manufacturer: Microchip Technology
• Series: DsPIC30Fr

Specifications of DSPIC30F5011-30I/PTG

• Core Frequency: 30MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 52
• Flash Memory Size: 66KB
• Supply Voltage Range: 2.5V To 5.5V
• Operating Temperature Range: -40°C To
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

23.0
This section provides an overview of dsPIC30F electrical characteristics. Additional information will be provided in future
revisions of this document as it becomes available.
For detailed information about the dsPIC30F architecture and core, refer to dsPIC30F Family Reference Manual
(DS70046).
Absolute maximum ratings for the dsPIC30F family are listed below. Exposure to these maximum rating conditions for
extended periods may affect device reliability. Functional operation of the device at these or any other conditions above
the parameters indicated in the operation listings of this specification is not implied.
Absolute Maximum Ratings
Ambient temperature under bias.............................................................................................................-40°C to +125°C
Storage temperature .............................................................................................................................. -65°C to +150°C
Voltage on any pin with respect to V
Voltage on V
Voltage on MCLR with respect to V
Total power dissipation (Note 2) ...............................................................................................................................1.0W
Maximum current out of V
Maximum current into V
Input clamp current, I
Output clamp current, I
Maximum output current sunk by any I/O pin..........................................................................................................25 mA
Maximum output current sourced by any I/O pin ....................................................................................................25 mA
Maximum current sunk by all ports .......................................................................................................................200 mA
Maximum current sourced by all ports ..................................................................................................................200 mA
 2004 Microchip Technology Inc.
†
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
Note 1: Power dissipation is calculated as follows:
Note:
2: Voltage spikes below V
ELECTRICAL CHARACTERISTICS
Pdis = V
Thus, a series resistor of 50-100 should be used when applying a “low” level to the MCLR/V
than pulling this pin directly to V
All peripheral electrical characteristics are specified. For exact peripherals available on specific
devices, please refer the the Family Cross Reference Table.
DD
with respect to V
DD
IK
OK
(V
x {I
DD
I
SS
(V
DD
< 0 or V
pin ..............................................................................................................................250 mA
O
pin ...........................................................................................................................300 mA
- ∑ I
< 0 or V
SS
OH
I
SS
SS
SS
> V
......................................................................................................... -0.3V to +5.5V
(†)
} + ∑ {(V
at the MCLR/V
(Note 1) ......................................................................................... 0V to +13.25V
O
(except V
DD
> V
) .......................................................................................................... ±20 mA
SS
DD
DD
.
) ...................................................................................................±20 mA
DD
- V
Preliminary
OH
and MCLR) ................................................... -0.3V to (V
PP
) x I
pin, inducing currents greater than 80 mA, may cause latchup.
OH
} + ∑(V
dsPIC30F5011/5013
O
l x I
OL
)
DS70116C-page 165
PP
DD
pin, rather
+ 0.3V)