ATMEGA325A-AUR Atmel, ATMEGA325A-AUR Datasheet - Page 302

• Manufacturer Part Number: ATMEGA325A-AUR
• Description: IC MCU AVR 32K FLASH 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA325A-AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

26.8.3
Table 26-16. Serial Programming Instruction Set
Notes:
302
Instruction/Operation
Programming Enable
Chip Erase (Program Memory/EEPROM)
Poll RDY/BSY
Load Instructions
Load Extended Address byte
Load Program Memory Page, High byte
Load Program Memory Page, Low byte
Load EEPROM Memory Page (page access)
Read Instructions
Read Program Memory, High byte
Read Program Memory, Low byte
Read EEPROM Memory
Read Lock bits
Read Signature Byte
Read Fuse bits
Read Fuse High bits
Read Extended Fuse Bits
Read Calibration Byte
Write Instructions
Write Program Memory Page
Write EEPROM Memory
Write EEPROM Memory Page (page access)
Write Lock bits
Write Fuse bits
Write Fuse High bits
Write Extended Fuse Bits
1. Not all instructions are applicable for all parts
2. a = address
3. Bits are programmed ‘0’, unprogrammed ‘1’.
4. To ensure future compatibility, unused Fuses and Lock bits should be unprogrammed (‘1’).
5. Refer to the corresponding section for Fuse and Lock bits, Calibration and Signature bytes and Page size.
6. Instructions accessing program memory use a word address. This address may be random within the page range.
7. See htt://www.atmel.com/avr for Application Notes regarding programming and programmers.
ATmega165A/165PA/325A/325PA/3250A/3250PA/645A/645P/645
Serial Programming Instruction set
(6)
Table 26-16
If the LSB in RDY/BSY data byte out is ‘1’, a programming operation is still pending. Wait until
this bit returns ‘0’ before the next instruction is carried out.
(1)
and
Figure 26-12 on page 303
Byte 1
$AC
$AC
$C1
$C0
$C2
$AC
$AC
$AC
$AC
$F0
$4D
$A0
$4C
$48
$40
$28
$20
$58
$30
$50
$58
$50
$38
0000 00aa
0000 00aa
0000 00aa
adr MSB
adr MSB
adr MSB
Byte 2
describes the Instruction set.
$E0
$A0
$A8
$A4
$53
$80
$00
$00
$00
$00
$00
$00
$00
$00
$08
$08
$00
Instruction Format
Extended adr
0000 00aa
aaaa aaaa
0000 00aa
aaaa aaaa
aaaa aa00
adr LSB
adr LSB
adr LSB
adr LSB
adr LSB
Byte 3
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
$00
high data byte out
low data byte out
high data byte in
low data byte in
data byte out
data byte out
data byte out
data byte out
data byte out
data byte out
data byte out
data byte out
data byte in
data byte in
data byte in
data byte in
data byte in
data byte in
8285B–AVR–03/11
Byte4
$00
$00
$00
$00
$00