IS-C0203-F-E NKK Switches, IS-C0203-F-E Datasheet - Page 15

• Manufacturer Part Number: IS-C0203-F-E
• Description: SMARTSWITCH CONTROLLER LCD
• Manufacturer: NKK Switches

Specifications of IS-C0203-F-E

• Accessory Type: Controller
• Description/function: SMARTSWITCH Development Kit
• For Use With/related Products: SmartSwitch™ Switches
• For Use With: 360-2345 - SWITCH COMPACT LCD 64X32 RGB360-2343 - SWITCH LCD 64X32 RGB360-2341 - DISPLAY LCD 64X32IS01BCEF - SMARTDISPLAY SUPER YEL/GRN LEDIS01BCE - SMARTDISPLAY SUPER YELLOW LEDIS15SBFP4B - SMARTSWITCH COMPACT WHITE LEDIS15SBCP4EF - SMARTSWITCH COMPACT YEL/GRN LEDIS15SACP4CF - SMARTSWITCH COMPACT RED/GRN LEDIS15ABFP4B - SMARTSWITCH STD BLK W/WHITE LEDIS15ABDP4B - SMARTSWITCH STD BLU W/WHITE LEDIS15ABDP4EG - SMARTSWITCH STD YELLOW/BLUE LEDIS15ABDP4E - SMARTSWITCH STD BLUE W/YEL LEDIS15ABCP4EF - SMARTSWITCH STD YEL/GRN LEDIS15ABCP4E - SMARTSWITCH STD LED YELLOWIS15AACP4CF - SMARTSWITCH STD YEL RED/GRN LED360-2334 - SMARTDISPLAY RED/GREEN/BLUE360-2333 - SMARTDISPLAY SUPER RED/GREEN LED360-2332 - SMARTSWITCH STANDARD RED/GRN/BLU360-2331 - SMARTSWITCH COMPACT RED/GRN/BLU360-2330 - SMARTSWITCH STD RED/GRN LED360-2329 - SMARTSWITCH COMPACT RED/GRN LED
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 360-2425

7850 East Gelding Drive • Scottsdale, AZ 85260-3420
Command to download FLAG B
[FLAG B] is one byte. See table below.
This command is for duration of the session. It can become permanent by “Command to write the setup
values to the EPROM”.
Command to set timers for LED up/ LED down
[Timer1] is one byte from 01H to FFH. 00H is not acceptable. Default (09H)
[Timer2] is one byte from 00H to FFH. 00H =256. Default (09H)
This command does not go to effect until it becomes permanent. It can become permanent by “Command to
write the setup values to the EPROM”.
Command to download power up Addresses
[Address for Switch 1] is one byte from 01H to FFH. 00H is not acceptable. Default (01H)
[Address for Switch 1] is one byte from 01H to FFH. 00H is not acceptable. Default (02H)
This command does not go to effect until it becomes permanent. It can become permanent by “Command to
C0203 User Manual.doc
This command sets Flag B.
This command sets the timers that determine the time “DOWN LED” and “UP LED” are displayed upon
power up. Every time the switches are pressed the timers get reset.
This command sets the addresses for switch 1 and switch 2 upon power up or reset.
write the setup values to the EPROM”.
B0
B1
B2
B3
B4
B5
B6
B7
Bit
command format:
transmit format:
Flag Byte B Default Value=01H
command format:
transmit format:
command format:
transmit format:
Enable
Value
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone [phone] • Fax [phone]
1
0
0
0
0
0
0
0
BEEPER
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
C0203 Intelligent Controller User Manual
(xxH) (xxH) (xxH)
(xxH) (xxH) (xxH) (xxAH)
(xxH) (xxH) (xxH)
26H
26H
26H
www.nkkswitches.com • Email [e-mail]
51H
51H
51H
Flag
5DH [Timer1] [Timer2]
5CH [FLAG B]
5EH [Address for Switch 1] [Address for Switch 2]
(xxAH)
(xxAH)
Beep for switch press
(xxAH)
Controller action when flag is set
(xxAH)
Page 15 of 23
0409