IS-C0203-F-E NKK Switches, IS-C0203-F-E Datasheet

Page 1

... C0203 Intelligent Controller User Manual NKK Switches makes no warranty for the use of these products and assumes no responsibility for any errors, which may appear in this document, nor does it make a commitment to update the information contained herein. Smart Switch is trademark of NKK Switches. C0203 User Manual.doc Toll Free 1.877.2BUYNKK (877.228.9655) • ...

Page 2

... Compatible Logic Boards.........................................................................................3 3. Operational Overview..............................................................................................4 4. Operational Details ...................................................................................................7 5. Communication Protocol .........................................................................................9 6. Hardware ...................................................................................................................18 7. Key Terms & Definitions..........................................................................................23 8. Firmware problems ..................................................................................................23 C0203 User Manual.doc Toll Free 1.877.2BUYNKK (877.228.9655) • Phone 480.991.0942 • Fax 480.998.1435 TABLE OF CONTENTS www.nkkswitches.com • Email engineering@nkkswitches.com Page 0409 ...

Page 3

... East Gelding Drive • Scottsdale, AZ 85260-3420 1. General Controller Features The C0203 controls two high resolution (64x32) switches/ displays or two standard (36x24) switches/ displays. The firmware can be customized based on customer requirements. Below are current features: • Controls two high resolution (64x32) switches/ displays or two standard (36x24) switches/ displays • ...

Page 4

... After a few seconds of user inactivity the controller will move into the main operations mode where the switch on the left displays the image at the user’s first preset address. The right hand switch will display the image at the user’s second preset address. The controller will then respond to a switch actuation or a timer expiration as set by the user preset attributes ...

Page 5

... East Gelding Drive • Scottsdale, AZ 85260-3420 LED Backlighting for 64x32 Resolution Switches: The LED code has two bytes, one byte for “on cycle” and one byte for “off cycle”. The format for both bytes is the same. Following is the byte format: ...

Page 6

... A block of 125 bytes. It contains picture data and LED codes. 116-120 122-125 LED Backlighting for 36x24 Resolution Switches: The LED code is one byte with the following format: B7=0 ==> Reserved B7=1 ==> Reserved B6=0 ==> Blue backlighting off during "OFF CYCLE" B6=1 ==> Blue backlighting on during "OFF CYCLE" ...

Page 7

... Step 1: Check the status of Mode Select Switch for mode of operation. Initialize according to selected mode. Step 2: Check if the flash RAM has been programmed. Compare the check string to flash RAM string the strings are not the same, the flash RAM is virgin and its data is not acceptable. Step 3 will be executed. (first time) B ...

Page 8

... A. The timer for the switch is reset and does not run until the switch is released byte 1 of the switch attributes is not equal to zero then the Legend block and attribute block from the EEPROM is transferred to internal RAM for switch 1. The Legend, backlighting and timer values are put in effect for switch 1 ...

Page 9

... B. If the byte is not a command ignored. When the controller executes a subroutine and expects additional information timer is set. If the expected data byte is not received in 50ms, the controller transmits 6EH and terminates the routine the byte value is not acceptable (invalid range, option, etc.), the controller transmits 6EH and terminates the routine ...

Page 10

... FFH sent as ASCII HEX format. The controller transmits back the image (125 bytes in standard resolution mode and is 256 bytes in high resolution mode) in HEX format. The controller disables the timers and switch execution upon receiving this command. However, the switches are still scanned and reported ...

Page 11

... [LED for switch 1] is one byte for standard resolution and two bytes for high resolution (first byte for on-cycle and second byte for off cycle). [LED for switch 2] is one byte for standard resolution and two bytes for high resolution (first byte for on-cycle and second byte for off cycle). ...

Page 12

... Module #] is the switch number (31H for switch 1, 32H for switch 2) [LED code] is one byte for standard resolution and two bytes for high resolution (first byte for on-cycle and second byte for off cycle). B0 and B1 must be 1 for high resolution. ...

Page 13

... BRIGHTNESS] is one byte from 00H (dimmest) to 07H (brightest). The upper 5 bits of the byte are ignored. This command is for duration of the session. It can become permanent by “Command to write the setup values to the EPROM”. ...

Page 14

... ON/OFF cycle] is one byte. Duration of ON cycle = ([LED ON/OFF]-1) *(duration of OFF cycle) This command is for duration of the session. It can become permanent by “Command to write the setup values to the EPROM”. Command to set FLAG A This command sets Flag A. ...

Page 15

... FFH. 00H is not acceptable. Default (09H) [Timer2] is one byte from 00H to FFH. 00H =256. Default (09H) This command does not go to effect until it becomes permanent. It can become permanent by “Command to write the setup values to the EPROM”. ...

Page 16

... C0203 Intelligent Controller User Manual 7850 East Gelding Drive • Scottsdale, AZ 85260-3420 Command to write the setup values to the EPROM This command writes the setup values to the flash as per the following table. Once commanded the values become permanent. command format: 26H transmit format: (xxH) (xxH) (xxH) (xxH) (xxH) • ...

Page 17

... Module #] is the switch number (31H for switch 1, 32H for switch 2) [ASCII string characters. The controller will make 3 lines of 8 characters using the 5x7 fonts for standard. Standard: 18 ASCII characters. High resolution: not available. Example: The following hex string makes switch 1 display standard resolution. ...

Page 18

... The Mode Select Switch has two settings; “High res” is for the High Resolution (64x32) switches/ displays and “Standard res” is for the Standard RGB switches/ displays. The Connector is for the installation of the Logic Boards onto the controller. One pin is keyed to reduce miss mates. ...

Page 19

... C0203 Intelligent Controller User Manual 7850 East Gelding Drive • Scottsdale, AZ 85260-3420 Controller Schematic Two Standard Resolution SmartSwitch, 36X24 RGB, logic board C0203 User Manual.doc Toll Free 1.877.2BUYNKK (877.228.9655) • Phone 480.991.0942 • Fax 480.998.1435 www.nkkswitches.com • Email engineering@nkkswitches.com Page 0409 ...

Page 20

... C0203 Intelligent Controller User Manual 7850 East Gelding Drive • Scottsdale, AZ 85260-3420 C0203 User Manual.doc Toll Free 1.877.2BUYNKK (877.228.9655) • Phone 480.991.0942 • Fax 480.998.1435 www.nkkswitches.com • Email engineering@nkkswitches.com Page 0409 ...

Page 21

... C0203 Intelligent Controller User Manual 7850 East Gelding Drive • Scottsdale, AZ 85260-3420 Two High Resolution SmartSwitch, 64X32 RGB, logic board C0203 User Manual.doc Toll Free 1.877.2BUYNKK (877.228.9655) • Phone 480.991.0942 • Fax 480.998.1435 www.nkkswitches.com • Email engineering@nkkswitches.com Page 0409 ...

Page 22

... C0203 Intelligent Controller User Manual 7850 East Gelding Drive • Scottsdale, AZ 85260-3420 Container size Board photo C0203 User Manual.doc Toll Free 1.877.2BUYNKK (877.228.9655) • Phone 480.991.0942 • Fax 480.998.1435 www.nkkswitches.com • Email engineering@nkkswitches.com Page 0409 ...

Page 23

... Address A one byte value ranging from 01H to FFH representing the 255 memory. 8. Firmware issues The problems found in the most current version are listed below and will be resolved in the following version. Version V11 1. Command 29H: High resolution does not upload complete data. ...