XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 37

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
D7 (DIO7 Configuration) Command
D8 (DI8 Configuration) Command
DA (Force Disassociation) Command
DB (Received Signal Strength) Command
DH (Destination Address High) Command
<I/O Settings> The D7 command is used to
select/read the behavior of the DIO7 line (pin 12).
Options include:
<I/O Settings> The D8 command is used to
select/read the behavior of the DI8 line (pin 9).
This command enables configuring the pin to
function as a digital input. This line is also used
with Pin Sleep.
<(Special)> The DA command is used to
immediately disassociate an End Device from a
Coordinator and reattempt to associate.
<Diagnostics> DB parameter is used to read the
received signal strength (in dBm) of the last RF
packet received. Reported values are accurate
between -40 dBm and the RF modem's receiver sensitivity.
Absolute values are reported. For example: 0x58 = -88 dBm (decimal). If no packets have been
received (since last reset, power cycle or sleep event), “0” will be reported.
<Networking {Addressing}> The DH command is
used to set and read the upper 32 bits of the RF
modem's 64-bit destination address. When
combined with the DL (Destination Address Low)
parameter, it defines the destination address
used for transmission.
An modem will only communicate with other
modems having the same channel (CH
parameter), PAN ID (ID parameter) and destination address
(DH + DL parameters).
To transmit using a 16-bit address, set the DH parameter to zero and the DL parameter less than
0xFFFF. 0x000000000000FFFF (DL concatenated to DH) is the broadcast address for the PAN.
Refer to the XBee/XBee-PRO Addressing section for more information.
• CTS flow control
• Analog-to-digital converter
• Digital input
• Digital output
AT Command: ATDA
Minimum Firmware Version Required: v1.x80
AT Command: ATDH
Parameter Range: 0 - 0xFFFFFFFF
Default Parameter Value: 0
Related Commands: DL (Destination Address
Low), CH (Channel), ID (PAN VID), MY (Source
Address)
AT Command: ATDB
Parameter Range: 0 - 0x64 [read-only]
AT Command: ATD7
Parameter Range:0 - 5
Default Parameter Value:1
Parameters 3-5 supported as of firmware
version 1.x.A0
AT Command: ATD8
Parameter Range:0 - 5
Default Parameter Value:0
Minimum Firmware Version Required: 1.xA0
Parameter
Parameter
0
1
2
3
4
5
0
3
(1, 2, 4 & 5 n/a)
CTS Flow Control
Configuration
Configuration
Disabled
Disabled
DO high
DO low
n/a
DI
DI
37