XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 30

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
Table 4‐06. XBee‐PRO Commands ‐ I/O Settings (sub‐category designated within {brackets})
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
Diagnostics
Table 4‐07. XBee‐PRO Commands ‐ Diagnostics
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
AT Command Options
Table 4‐08. XBee‐PRO Commands ‐ AT Command Options
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
AT
Command
P1 (v1.xA0*)
M0 (v1.xA0*)
M1 (v1.xA0*)
PT (v1.xA0*)
RP
AT
Command
VR
VL (v1.x80*)
HV (v1.x80*)
DB
EC (v1.x80*)
EA (v1.x80*)
ED (v1.x80*)
AT
Command
CT
CN
AC (v1.xA0*)
GT
CC
Command
Category
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
Command
Category
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Diagnostics
Command
Category
AT Command
Mode Options
AT Command
Mode Options
AT Command
Mode Options
AT Command
Mode Options
AT Command
Mode Options
Name and Description
PWM1 Configuration. Select/Read function for PWM1 pin.
PWM0 Output Level. Set/Read the PWM0 output level.
PWM1 Output Level. Set/Read the PWM0 output level.
PWM Output Timeout. Set/Read output timeout value for both PWM outputs. When
PWM is set to a non-zero value: Due to I/O line passing, a time is started which when
expired will set the PWM output to zero. The timer is reset when a valid I/O packet is
received.]
RSSI PWM Timer. Set/Read PWM timer register. Set the duration of PWM (pulse width
modulation) signal output on the RSSI pin. The signal duty cycle is updated with each
received packet and is shut off when the timer expires.]
Name and Description
Firmware Version. Read firmware version of the RF modem.
Firmware Version - Verbose. Read detailed version information (including application
build date, MAC, PHY and bootloader versions).
Hardware Version. Read hardware version of the RF modem.
Received Signal Strength. Read signal level [in dB] of last good packet received
(RSSI). Absolute value is reported. (For example: 0x58 = -88 dBm) Reported value is
accurate between -40 dBm and RX sensitivity.
CCA Failures. Reset/Read count of CCA (Clear Channel Assessment) failures. This
parameter value increments when the modem does not transmit a packet because it
detected energy above the CCA threshold level set with CA command. This count
saturates at its maximum value. Set count to “0” to reset count.
ACK Failures. Reset/Read count of acknowledgment failures. This parameter value
increments when the modem expires its transmission retries without receiving an ACK
on a packet transmission. This count saturates at its maximum value. Set the parameter
to “0” to reset count.
Energy Scan. Send ‘Energy Detect Scan’. ED parameter determines the length of scan
on each channel. The maximal energy on each channel is returned and each value is
followed by a carriage return. Values returned represent detected energy levels in units
of -dBm. Actual scan time on each channel is measured as Time = [(2 ^ SD) * 15.36]
ms. Total scan time is this time multiplied by the number of channels to be scanned.
Name and Description
Command Mode Timeout. Set/Read the period of inactivity (no valid commands
received) after which the RF modem automatically exits AT Command Mode and
returns to Idle Mode.
Exit Command Mode. Explicitly exit the modem from AT Command Mode.
Apply Changes. Explicitly apply changes to queued parameter value(s) and re-
initialize modem.
Guard Times. Set required period of silence before and after the Command Sequence
Characters of the AT Command Mode Sequence (GT+ CC + GT). The period of silence
is used to prevent inadvertent entrance into AT Command Mode.
Command Sequence Character. Set/Read the ASCII character value to be used
between Guard Times of the AT Command Mode Sequence (GT+CC+GT). The AT
Command Mode Sequence enters the RF modem into AT Command Mode.
Parameter Range
0 - 2
0 - 0x03FF
0 - 0x03FF
0 - 0xFF [x 100 ms]
0 - 0xFF [x 100 ms]
Parameter Range
0 - 0xFFFF [read-only]
-
0 - 0xFFFF [read-only]
0 - 0x64 [read-only]
0 - 0xFFFF
0 - 0xFFFF
0 - 6
Parameter Range
2 - 0xFFFF [x 100 ms]
--
--
2 - 0x0CE4 [x 1 ms]
0 - 0xFF
0 = Disabled
1 = RSSI
2 = PWM Output
Default
0
-
-
0xFF
0x28 (40d)
Default
Factory-set
-
Factory-set
-
-
-
-
Default
0x64 (100d)
--
--
0x3E8
(1000d)
0x2B
(‘+’ ASCII)
30