XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 24

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
Special
Table 4‐01. XBee‐PRO Commands ‐ Special
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
Networking & Security
Table 4‐02. XBee‐PRO Commands ‐ Networking & Security (Sub‐categories designated within {brackets})
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
AT
Command
WR
RE
FR ( v1.x80*)
AT
Command
CH
ID
DH
DL
MY
SH
SL
RR ( v1.xA0*)
RN
MM ( v1.x80*)
NI ( v1.x80*)
4.2. Command Reference Tables
Command
Category
Special
Special
Special
Command
Category
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Addressing}
Networking
{Identification}
XBee-PRO RF Modems expect numerical values in hexadecimal. Hexadecimal values are
designated by a “0x” prefix. Decimal equivalents are designated by a “d” suffix. Table rows are
sorted by command category, then by logic of most commonly used.
All modems operating within the same network should contain the same firmware version.
Name and Description
Write. Write parameter values to non-volatile memory so that parameter modifications
persist through subsequent power-up or reset.
Note: Once WR is issued, no additional characters should be sent to the modem until
after the response "OK\r" is received.
Restore Defaults. Restore modem parameters to factory defaults.
Software Reset. Responds immediately with an OK then performs a hard reset
~100ms later.
Name and Description
Channel. Set/Read the channel number used for transmitting and receiving data
between RF modems (uses 802.15.4 protocol channel numbers).
PAN ID. Set/Read the PAN (Personal Area Network) ID.
Use 0xFFFF to broadcast messages to all PANs.
Destination Address High. Set/Read the upper 32 bits of the 64-bit destination
address. When combined with DL, it defines the destination address used for
transmission. To transmit using a 16-bit address, set DH parameter to zero and DL less
than 0xFFFF. 0x000000000000FFFF is the broadcast address for the PAN.
Destination Address Low. Set/Read the lower 32 bits of the 64-bit destination
address. When combined with DH, DL defines the destination address used for
transmission. To transmit using a 16-bit address, set DH parameter to zero and DL less
than 0xFFFF. 0x000000000000FFFF is the broadcast address for the PAN.
16-bit Source Address. Set/Read the RF modem 16-bit source address. Set MY =
0xFFFF to disable reception of packets with 16-bit addresses. 64-bit source address
(serial number) and broadcast address (0x000000000000FFFF) is always enabled.
Serial Number High. Read high 32 bits of the RF modem's unique IEEE 64-bit
address. 64-bit source address is always enabled.
Serial Number Low. Read low 32 bits of the RF modem's unique IEEE 64-bit address.
64-bit source address is always enabled.
XBee Retries. Set/Read the maximum number of retries the modem will execute in
addition to the 3 retries provided by the 802.15.4 MAC. For each XBee retry, the
802.15.4 MAC can execute up to 3 retries.
Random Delay Slots. Set/Read the minimum value of the back-off exponent in the
CSMA-CA algorithm that is used for collision avoidance. If RN = 0, collision avoidance
is disabled during the first iteration of the algorithm (802.15.4 - macMinBE).
MAC Mode. Set/Read MAC Mode value. MAC Mode enables/disables the use of a Digi
header in the 802.15.4 RF packet. When Mode 0 is enabled (MM=0), duplicate packet
detection is enabled as well as certain AT commands. Modes 1 and 2 are strict
802.15.4 modes.
Node Identifier. Stores a string identifier. The register only accepts printable ASCII
data. A string can not start with a space. Carriage return ends command. Command will
automatically end when maximum bytes for the string have been entered. This string is
returned as part of the ND (Node Discover) command. This identifier is also used with
the DN (Destination Node) command.
Parameter Range
-
-
-
Parameter Range
0x0C - 0x17
0 - 0xFFFF
0 - 0xFFFFFFFF
0 - 0xFFFFFFFF
0 - 0xFFFF
0 - 0xFFFFFFFF [read-only]
0 - 0xFFFFFFFF [read-only]
0 - 6
0 - 3 [exponent]
0 - 2
20-character ASCII string
0 = Digi Mode
1 = 802.15.4 (no ACKs)
2 = 802.15.4 (with ACKs)
Default
-
-
-
Default
0x0C (12d)
0x3332
(13106d)
0
0
0
Factory-set
Factory-set
0
0
0
-
24