XBP24-PKI-001-RA Digi International/Maxstream, XBP24-PKI-001-RA Datasheet - Page 29

• Manufacturer Part Number: XBP24-PKI-001-RA
• Description: MODULE 802.15.4 RS-232 ANT
• Manufacturer: Digi International/Maxstream
• Series: XBEE-PRO™r

Specifications of XBP24-PKI-001-RA

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Data Interface: Connector, Female DB-9
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Memory Size: -
• Current - Transmitting: -
• Other names: Q3255595

© 2008 Digi International, Inc.
I/O Settings
Table 4‐06. XBee‐PRO Commands ‐ I/O Settings (sub‐category designated within {brackets})
XBee‐PRO PKG‐R® RS‐232 RF Modem – 802.15.4 ‐ Product Manual v1.xAx
AT
Command
D8
D7 (v1.x80*)
D6 (v1.x80*)
D5 (v1.x80*)
D0 - D4
(v1.xA0*)
IU (v1.xA0*)
IT (v1.xA0*)
IS (v1.xA0*)
IO (v1.xA0*)
IC (v1.xA0*)
IR (v1.xA0*)
AV (v1.xA0*)
IA (v1.xA0*)
T0 - T7
(v1.xA0*)
P0
NOTE: The “I/O Settings” commands listed below refer to the I/O lines of the OEM RF module embedded inside the boxed
RF modem. Implementation of these commands requires board-level development and is not supported when using the
DB-9 serial connection of the RF modem.
Command
Category
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
I/O Settings {I/O
Line Passing}
Name and Description
DI8 Configuration. Select/Read options for the DI8 line (pin 9) of the RF modem.
DIO7 Configuration. Select/Read settings for the DIO7 line (pin 12) of the RF modem.
Options include CTS flow control and I/O line settings.
DIO6 Configuration. Select/Read settings for the DIO6 line (pin 16) of the RF modem.
Options include RTS flow control and I/O line settings.
DIO5 Configuration. Configure settings for the DIO5 line (pin 15) of the RF modem.
Options include Associated LED indicator (blinks when associated) and I/O line
settings.
(DIO4 -DIO4) Configuration. Select/Read settings for the following lines: AD0/DIO0
(pin 20), AD1/DIO1 (pin 19), AD2/DIO2 (pin 18), AD3/DIO3 (pin 17), AD4/DIO4 (pin 11).
Options include: Analog-to-digital converter, Digital Input and Digital Output.
I/O Output Enable. Disables/Enables I/O data received to be sent out UART. The data
is sent using an API frame regardless of the current AP parameter value.
Samples before TX. Set/Read the number of samples to collect before transmitting
data. Maximum number of samples is dependent upon the number of enabled inputs.
Force Sample. Force a read of all enabled inputs (DI or ADC). Data is returned through
the UART. If no inputs are defined (DI or ADC), this command will return error.
Digital Output Level. Set digital output level to allow DIO lines that are setup as
outputs to be changed through Command Mode.
DIO Change Detect. Set/Read bitfield values for change detect monitoring. Each bit
enables monitoring of DIO0 - DIO7 for changes. If detected, data is transmitted with
DIO data only. Any samples queued waiting for transmission will be sent first.
Sample Rate. Set/Read sample rate. When set, this parameter causes the modem to
sample all enabled inputs at a specified interval.
ADC Voltage Reference. <XBee-PRO only> Set/Read ADC reference voltage switch.
I/O Input Address. Set/Read addresses of modem to which outputs are bound. Setting
all bytes to 0xFF will not allow any received I/O packet to change outputs. Setting
address to 0xFFFF will allow any received I/O packet to change outputs.
(D0 - D7) Output Timeout. Set/Read Output timeout values for lines that correspond
with the D0 - D7 parameters. When output is set (due to I/O line passing) to a non-
default level, a timer is started which when expired will set the output to it default level.
The timer is reset when a valid I/O packet is received.
PWM0 Configuration. Select/Read function for PWM0 pin.
Parameter Range
0 - 1
(1,2,4 & 5 n/a)
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
1 - 0xFF
8-bit bitmap (each bit
represents the level of an I/O
line setup as an output)
-
0 - 0xFF [bitfield]
0 - 0xFFFF [x 1 msec]
0 - 1
0 - 0xFFFFFFFFFFFFFFFF
0 - 0xFF [x 100 ms]
0 - 2
0 = Disabled
3 = DI
0 = Disabled
1 = CTS Flow Control
2 = (n/a)
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = RTS flow control
2 = (n/a)
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = Associated indicator
2 = ADC
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = (n/a)
2 = ADC
3 = DI
4 = DO low
5 = DO high
0 = Disabled
1 = Enabled
0 = VREF pin
1 = Internal
0 = Disabled
1 = RSSI
2 = PWM Output
Default
0
1
0
1
0
1
1
-
-
0 (disabled)
0
0
0xFFFFFFF
FFFFFFFFF
0xFF
1
29