ATA3745P3-TGQY Atmel, ATA3745P3-TGQY Datasheet - Page 7

• Manufacturer Part Number: ATA3745P3-TGQY
• Description: IC UHF ASK/FSK RECEIVER 20SOIC
• Manufacturer: Atmel

Specifications of ATA3745P3-TGQY

• Frequency: 310MHz ~ 440MHz
• Sensitivity: -108dBm
• Data Rate - Maximum: 10 kBaud
• Modulation Or Protocol: ASK, FSK
• Applications: RKE, TPM, Security Systems
• Current - Receiving: 7mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: ATA3745P3-TGQYTR

4. Analog Signal Processing
4.1
4.2
4.3
4901B–RKE–11/07
IF Amplifier
RSSI Amplifier
Demodulator and Data Filter
The signals coming from the RF front end are filtered by the fully integrated 4th-order IF filter.
Th e IF cente r frequ ency is f
f
determine the center frequency.
The receiver ATA3745 employs an IF bandwidth of B
together with the ATA2745. SAW transmitters exhibit much higher transmit frequency toler-
ances compared to PLL transmitters. Generally, it is necessary to use B
with such transmitters.
The subsequent RSSI amplifier enhances the output signal of the IF amplifier before it is fed
into the demodulator. The dynamic range of this amplifier is R
fier is operated within its linear range, the best signal-to-noise ratio (SNR) is maintained in
ASK mode. If the dynamic range is exceeded by the transmitter signal, the SNR is defined by
the ratio of the maximum RSSI output voltage and the RSSI output voltage due to a disturber.
The dynamic range of the RSSI amplifier is exceeded if the RF input signal is about 60 dB
higher compared to the RF input signal at full sensitivity.
Since different RF input networks may exhibit slightly different values for the LNA gain, the
sensitivity values given in the electrical characteristics refer to a specific input matching. This
matching is illustrated in
The signal coming from the RSSI amplifier is converted into the raw data signal by the ASK
demodulator.
In ASK mode, an automatic threshold control (ATC) circuit is employed to set the detection ref-
erence voltage to a value where a good SNR is achieved. This circuit also implies the effective
suppression of any kind of in-band noise signals or competing transmitters. If the SNR
exceeds 10 dB, the data signal can be detected properly.
The output signal of the demodulator is filtered by the data filter before it is fed into the digital
signal processing circuit. The data filter improves the SNR as its band-pass can be adapted to
the characteristics of the data signal. The data filter consists of a 1st-order high-pass and a
1st-order low-pass filter.
The high-pass filter cut-off frequency is defined by an external capacitor connected to pin
CDEM. The cut-off frequency of the high-pass filter is defined by the following formula:
In self-polling mode, the data filter must settle very rapidly to achieve a low current consump-
tion. Therefore, CDEM cannot be increased to very high values if self polling is used. On the
other hand, CDEM must be large enough to meet the data filter requirements according to the
data signal. Recommended values for CDEM are given in the section
tics” on page
f
RF
cu_DF
= 433.92 MHz is used. For other RF input frequencies, refer to
=
------------------------------------------------------------ -
2
23.
30 k
1
CDEM
Figure 3-3 on page 6
I F
= 1 M Hz for app lication s whe re f
and exhibits the best possible sensitivity.
IF
= 600 kHz. This IC can be used
RSSI
= 60 dB. If the RSSI ampli-
Table 3-1 on page 5
“Electrical Characteris-
IF
= 600 kHz together
R F
ATA3745
= 3 15 M Hz o r
to
7