MCF5280CVM66 Freescale Semiconductor, MCF5280CVM66 Datasheet - Page 537

• Manufacturer Part Number: MCF5280CVM66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5280CVM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• No. Of I/o's: 150
• Program Memory Size: 2KB
• Ram Memory Size: 64KB
• Cpu Speed: 66.67MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

During reset, certain module configurations depend on whether emulation mode is active as determined
by the state of the internal emulation signal.
27.6.3
During reset configuration, the CS0 chip select pin is optionally configured to select an external boot
device. In this case, the V (valid) bit in the CSMR0 register is ignored, and CS0 is enabled after reset. CS0
is asserted for the initial boot fetch accessed from address 0x0000_0000 for the Stack Pointer and address
0x0000_0004 for the program counter (PC). It is assumed that the reset vector loaded from address
0x0000_0004 causes the CPU to start executing from external memory space decoded by CS0.
27.6.4
Output pad strength is determined during reset configuration as shown in
the output pad strength configuration can be changed by programming the LOAD bit of the chip
configuration register.
27.6.5
The clock mode is selected during reset by the CLKMOD pins and reflected in the PLLMODE, PLLSEL,
and PLLREF bits of SYNSR. After reset is exited, the clock mode cannot be changed.
Table 27-11
Freescale Semiconductor
Boot Device Selection
Output Pad Strength Configuration
Clock Mode Selection
summarizes clock mode selection during reset configuration.
1
1
Output pads configured for partial strength
Output pads configured for full strength
When Flash security is enabled, the chip will boot in single chip mode
regardless of the external reset configuration.
Modifying the default configurations is possible only if the external RCON pin is asserted low.
Modifying the default configurations is possible only if the external RCON pin is asserted low.
Chip Configuration
Single-chip mode
Master mode
Reserved
Reserved
Mode
Optional Pin Function Selection
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
Table 27-10. Output Pad Driver Strength Selection
Table 27-9. Chip Configuration Mode Selection
D26 driven high
D26 driven high
D26 driven high
D26 driven low
MODE2
NOTE
CCR Register MODE Field
D17 driven high
D17 driven high
D17 driven low
D17 don’t care
MODE1
CCR Register LOAD Bit
D21 driven high
D21 driven low
Table
1
D16 driven high
D16 driven high
D16 driven low
D16 don’t care
1
Chip Configuration Module (CCM)
27-10. Once reset is exited,
MODE0
27-9