MCF5280CVM66 Freescale Semiconductor, MCF5280CVM66 Datasheet - Page 127

• Manufacturer Part Number: MCF5280CVM66
• Description: IC MPU 32BIT COLDF 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5280CVM66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 142
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• No. Of I/o's: 150
• Program Memory Size: 2KB
• Ram Memory Size: 64KB
• Cpu Speed: 66.67MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

6.3.4.7
The CFMUSTAT reports Flash state machine command status, array access errors, protection violations,
and blank check status.
Freescale Semiconductor
Bits
7
6
5
4
3
CFM User Status Register (CFMUSTAT)
Address
Only one CFMUSTAT bit should be cleared at a time.
Reset
Field
R/W
ACCERR
CBEIF
PVIOL
Name
CCIF
—
CBEIF
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
R/W
7
Figure 6-11. CFM User Status Register (CFMUSTAT)
Command buffer empty interrupt flag. The CBEIF flag indicates that the command
buffer for the interleaved Flash physical blocks is empty and that a new command
sequence can be started. Clear CBEIF by writing it to 1. Writing a 0 to CBEIF has
no effect but can be used to abort a command sequence. The CBEIF bit can trigger
an interrupt request if the CBEIE bit is set in CFMMCR. While CBEIF is clear, the
CFMCMD register is not writable.
1 Command buffer is ready to accept a new command.
0 Command buffer is full.
Command complete interrupt flag. The CCIF flag indicates that no commands are
pending for the Flash physical blocks. CCIF is set and cleared automatically upon
start and completion of a command. Writing to CCIF has no effect. The CCIF bit
can trigger an interrupt request if the CCIE bit is set in CFMCR.
1 All commands are completed
0 Command in progress
Protection violation flag. The PVIOL flag indicates an attempt was made to initiate
a program or erase operation in a Flash logical sector denoted as protected by
CFMPROT. Clear PVIOL by writing it to 1. Writing a 0 to PVIOL has no effect. While
PVIOL is set in any this register, it is not possible to launch another command.
1 A protection violation has occurred
0
Access error flag. The ACCERR flag indicates an illegal access to the CFM array
or registers caused by a bad program or erase sequence. ACCERR is cleared by
writing it to 1. Writing a 0 to ACCERR has no effect. While ACCERR is set in this
register, it is not possible to launch another command. See
User Mode Illegal
1 Access error has occurred
0
Reserved, should be cleared.
Table 6-10. CFMUSTAT Field Descriptions
CCIF
No failure
No failure
R
6
PVIOL ACCERR
5
Operations,” for details on what sets the ACCERR flag.
IPSBAR + 0x1D_0020
NOTE
1100_0000
—
Description
R/W
BLANK
1
Section 6.4.3.4, “Flash
ColdFire Flash Module (CFM)
—
0
6-15