DF2378RVFQ34WV Renesas Electronics America, DF2378RVFQ34WV Datasheet - Page 991

• Manufacturer Part Number: DF2378RVFQ34WV
• Description: MCU 3V 512K I-TEMP PB-FREE 144-L
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of DF2378RVFQ34WV

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 34MHz
• Connectivity: I²C, IrDA, SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 97
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• For Use With: YLCDRSK2378 - KIT DEV EVAL H8S/2378 LCDYR0K42378FC000BA - KIT EVAL FOR H8S/2378HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)EDK2378 - DEV EVAL KIT FOR H8S/2378
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

21.6
It is possible to alternate between the user MAT and user boot MAT. However, the following
procedure is required because these MATs are allocated to address 0.
(Switching to the user boot MAT disables programming and erasing. Programming of the user
boot MAT should take place in boot mode or PROM mode.)
1. MAT switching by FMATS should always be executed from the on-chip RAM.
2. To ensure that the MAT that has been switched to is accessible, execute four NOP instructions
3. If an interrupt has occurred during switching, there is no guarantee of which memory MAT is
4. After the MATs have been switched, take care because the interrupt vector table will also have
5. Memory sizes of the user MAT and user boot MAT are different. When accessing the user
in the on-chip RAM immediately after writing to FMATS of the on-chip RAM (this prevents
access to the flash memory during MAT switching).
being accessed. Always mask the maskable interrupts before switching between MATs. In
addition, configure the system so that NMI interrupts do not occur during MAT switching.
been switched. If interrupt processing is to be the same before and after MAT switching,
transfer the interrupt-processing routines to the on-chip RAM, and use the settings of FVACR
to place the interrupt-vector table in the on-chip RAM .
boot MAT, do not access addresses above the top of its 8-kbyte memory space. If access goes
beyond the 8-kbyte space, the values read are undefined.
Switching between User MAT and User Boot MAT
Figure 21.16 Switching between the User MAT and User Boot MAT
< User MAT >
Procedure for switching to the user boot MAT
(1) Mask interrupts
(2) Write H'AA to FMATS.
(3) Execute four NOP instructions before
Procedure for switching to the user MAT
(1) Mask interrupts
(2) Write a value other than H'AA to FMATS.
(3) Execute four NOP instructions before accessing
accessing the user boot MAT.
the user MAT.
< On-chip RAM >
switching to the
user boot MAT
Procedure for
Procedure for
the user MAT
switching to
Section 21 Flash Memory (0.18-μm F-ZTAT Version)
Rev.7.00 Mar. 18, 2009 page 923 of 1136
< User boot MAT >
REJ09B0109-0700