STM32F103C8T6TR STMicroelectronics, STM32F103C8T6TR Datasheet - Page 26

no-image

STM32F103C8T6TR

Manufacturer Part Number
STM32F103C8T6TR
Description
MCU ARM 64KB FLASH MEM 48-LQFP
Manufacturer
STMicroelectronics
Series
STM32r

Specifications of STM32F103C8T6TR

Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
72MHz
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
Peripherals
DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
Number Of I /o
37
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
20K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 10x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-LQFP
For Use With
497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8511 - KIT STARTER FOR STM32 512K FLASH497-6438 - BOARD EVALUTION FOR STM32 512K
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STM32F103C8T6TR
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F103C8T6TR
Manufacturer:
STM
Quantity:
12 000
Part Number:
STM32F103C8T6TR
Manufacturer:
ST
0
Part Number:
STM32F103C8T6TR
0
Electrical characteristics
5.2
26/67
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 5: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 4.
1. All 3.3 V power (V
2. I
Table 5.
1. All 3.3 V power (V
2. I
3. Negative injection disturbs the analog performance of the device. See note in
4. When several inputs are submitted to a current injection, the maximum I
|V
V
I
V
INJ(PIN)
supply.
maximum is respected. If V
externally to the I
induced by V
supply.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
characteristics.
positive and negative injected currents (instantaneous values). These results are based on
characterization with I
Symbol
SSX
INJ(PIN)
INJ(PIN)
| V
ESD(HBM)
DD
I
Symbol
INJ(PIN)
V
I
I
–V
VDD
VSS
DDx
I
IN
IO
V
SS
(2)(3)
must never be exceeded (see
must never be exceeded. This is implicitly insured if V
|
SS
(2)
|
Voltage characteristics
Current characteristics
IN
External 3.3 V supply voltage (including V
and V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different power pins
Variations between all the different ground pins
Electrostatic discharge voltage (human body
model)
< V
characteristics, and
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on HSE OSC_IN and LSE OSC_IN pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
INJ(PIN)
DD
DD
SS
, V
, V
DD
.
INJ(PIN)
DDA
DDA
)
IN
value. A positive injection is induced by V
(1)
> V
) and ground (V
IN
) and ground (V
maximum cannot be respected, the injection current must be limited
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Ratings
DD
Table 5: Current
SS
Table 6: Thermal characteristics
power lines (source)
SS
SS
ground lines (sink)
, V
, V
Ratings
(2)
SSA
SSA
) pins must always be connected to the external 3.3 V
) pins must always be connected to the external 3.3 V
(4)
(2)
characteristics). This is implicitly insured if V
DDA
IN
maximum is respected. If V
(1)
(1)
Table 4: Voltage
IN
>V
Absolute maximum ratings
DD
V
V
INJ(PIN)
(electrical sensitivity)
while a negative injection is
SS
SS
IN
see
–0.3
INJ(PIN)
Min
50
50
(4)
< V
Section 5.3.17: 12-bit ADC
0.3
0.3
Section 5.3.11:
SS
is the absolute sum of the
may cause permanent
.
value. A positive
characteristics,
V
Max.
± 25
150
150
± 5
± 5
± 5
DD
25
Max
+5.5
STM32F103xx
IN
25
4.0
50
50
+0.3
maximum
IN
Unit
mA
Unit
mV
V

Related parts for STM32F103C8T6TR