AT32UC3A0128-ALUR Atmel, AT32UC3A0128-ALUR Datasheet - Page 390

• Manufacturer Part Number: AT32UC3A0128-ALUR
• Description: MCU AVR32 128K FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3A0128-ALUR

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, SSC, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 109
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Package: 144LQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 66 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 69
• Interface Type: Ethernet/I2S/JTAG/SPI/TWI/USART
• Number Of Timers: 3
• For Use With: ATEVK1105 - KIT EVAL FOR AT32UC3A0ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMR770-1008 - ISP 4PORT ATMEL AVR32 MCU SPIATEVK1100 - KIT DEV/EVAL FOR AVR32 AT32UC3A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

27.6.6.2
Figure 27-23. TDF Optimization: No TDF wait states are inserted if the TDF period is over when the next access begins
27.6.6.3
32058J–AVR32–04/11
CLK_SMC
D[15:0]
A[25:2]
NCS0
NWE
NRD
TDF Optimization Enabled (TDF_MODE = 1)
TDF Optimization Disabled (TDF_MODE = 0)
Read access on NCS0 (NRD controlled)
When the TDF_MODE of the MODE register is set to 1 (TDF optimization is enabled), the SMC
takes advantage of the setup period of the next access to optimize the number of wait states
cycle to insert.
Figure 27-23
NWE, on Chip Select 0. Chip Select 0 has been programmed with:
NRD_HOLD = 4; READ_MODE = 1 (NRD controlled)
NWE_SETUP = 3; WRITE_MODE = 1 (NWE controlled)
TDF_CYCLES = 6; TDF_MODE = 1 (optimization enabled).
When optimization is disabled, tdf wait states are inserted at the end of the read transfer, so that
the data float period is ended when the second access begins. If the hold period of the read1
controlling signal overlaps the data float period, no additional tdf wait states will be inserted.
Figure
• read access followed by a read access on another chip select,
• read access followed by a write access on another chip select,
27-24,
shows a read access controlled by NRD, followed by a write access controlled by
NRD_HOLD = 4
Figure 27-25
TDF_CYCLES = 6
and
Figure 27-26
Read to Write
Wait State
NWE_SETUP = 3
illustrate the cases:
write access on NCS0 (NWE controlled)
AT32UC3A
390