MC56F8013VFAE Freescale Semiconductor, MC56F8013VFAE Datasheet - Page 99

• Manufacturer Part Number: MC56F8013VFAE
• Description: IC DIGITAL SIGNAL CTLR 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8013VFAE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 2K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-LQFP
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: MC56F80xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 32 MIPs
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 26
• Data Ram Size: 4 KB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Rom Size: 16 KB
• Development Tools By Supplier: MC56F8037EVM, DEMO56F8014-EE, DEMO56F8013-EE
• Interface Type: SCI, SPI, I2C
• Minimum Operating Temperature: - 40 C
• For Use With: CPA56F8013 - BOARD SOCKET FOR MC56F8013APMOTOR56F8000E - KIT DEMO MOTOR CTRL SYSTEMDEMO56F8013-EE - BOARD DEMO FOR 56F8013
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

10.2.1
The 56F8013/56F8011 have two on-chip regulators. One supplies the PLL and relaxation oscillator. It has
no external pins and therefore has no external characteristics which must be guaranteed (other than proper
operation of the device). The second regulator supplies approximately 2.5V to the 56F8013/56F8011’s
core logic. This regulator requires an external 2.2
and tantalum capacitors tend to provide better performance tolerances. The output voltage can be
measured directly on the V
10.3 AC Electrical Characteristics
Tests are conducted using the input levels specified in
propagation delays are measured from the 50% to the 50% point, and rise and fall times are measured
between the 10% and 90% points, as shown in
Freescale Semiconductor
Short Circuit Current
Short Circuit Tolerance
(output shorted to ground)
1. When V
2. When V
3. Power-On Reset occurs whenever the internally regulated 2.5V digital supply drops below 1.8V. While
Low-Voltage Interrupt for 3.3V supply
Low-Voltage Interrupt for 2.5V supply
Low-Voltage Interrupt Recovery Hysteresis
Power-On Reset
power is ramping up, this signal remains active for as long as the internal 2.5V is below 2.15V or the 3.3V
1/O voltage is below 2.7V, no matter how long the ramp-up rate is. The internally regulated voltage is
typically 100mV less than V
Voltage Regulator Specifications
Characteristic
DD
DD
drops below V
drops below V
Table 10-7 Power-On Reset Low-Voltage Parameters
Characteristic
3
CAP
EI3.3
EI32.5
pin. The specifications for this regulator are shown in
Table 10-8. Regulator Parameters
DD
, an interrupt is generated.
, an interrupt is generated.
during ramp-up until 2.5V is reached, at which time it self-regulates.
56F8013/56F8011 Data Sheet, Rev. 12
1
2
Symbol
T
I
RSC
SS
Figure
Symbol
μ
V
F, or greater, capacitor for proper operation. Ceramic
V
POR
V
E12.5
EI3.3
EIH
10-2.
Min
—
—
2.58
Min
Table
—
—
—
Typical
450
—
10-5. Unless otherwise specified,
2.15
Typ
2.7
1.8
50
Max
650
30
Max
1.9
—
—
—
AC Electrical Characteristics
Table
Unit
mV
V
V
V
Minutes
10-8.
Unit
mA
99