MC56F8013VFAE Freescale Semiconductor, MC56F8013VFAE Datasheet - Page 86

• Manufacturer Part Number: MC56F8013VFAE
• Description: IC DIGITAL SIGNAL CTLR 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8013VFAE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 2K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-LQFP
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: MC56F80xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 32 MIPs
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 26
• Data Ram Size: 4 KB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Rom Size: 16 KB
• Development Tools By Supplier: MC56F8037EVM, DEMO56F8014-EE, DEMO56F8013-EE
• Interface Type: SCI, SPI, I2C
• Minimum Operating Temperature: - 40 C
• For Use With: CPA56F8013 - BOARD SOCKET FOR MC56F8013APMOTOR56F8000E - KIT DEMO MOTOR CTRL SYSTEMDEMO56F8013-EE - BOARD DEMO FOR 56F8013
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7.2.4
The user can un-secure a secured device by programming the word $0000 into program memory location
$00 1FF7. After completing the programming, both the JTAG TAP controller and the device must be
reset in order to return to normal unsecured operation. Power-on reset will also reset both.
The user is responsible for directing the device to invoke the flash programming subroutine to reprogram
the word $0000 into program memory location $00 1FF7. This is done by, for example, toggling a specific
pin, or by downloading a user-defined key through serial interfaces.
Note:
7.3 Product Analysis
The recommended method of unsecuring a secured device for product analysis of field failures is via the
method suggested in
of the protocol to access the subroutines in flash. An alternative method for performing analysis on a
secured device would be to mass-erase and reprogram the flash with the original code, but also either
modify the security word or else not program the security word.
Part 8 General Purpose Input/Output (GPIO)
8.1 Introduction
This section is intended to supplement the GPIO information found in the 56F801X Peripheral User
Manual and contains only chip-specific information. This information supercedes the generic information
in the 56F801X Peripheral User Manual.
8.2 Configuration
There are four GPIO ports defined on the 56F8013/56F8011. The width of each port, the associated
peripheral and reset functions are shown in
in
86
Table
8-2.
Flash Lockout Recovery Without Mass Erase
Flash contents can only be programmed for 1s to 0s.
Section
7.2.4. The customer would need to supply Technical Support with the details
56F8013/56F8011 Data Sheet, Rev. 12
Table
8-1. The specific mapping of GPIO port pins is shown
Freescale Semiconductor