MC908AP32CFAE Freescale Semiconductor, MC908AP32CFAE Datasheet - Page 199

• Manufacturer Part Number: MC908AP32CFAE
• Description: IC MCU 32K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP32CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

12.9.4 IRSCI Status Register 1
SCI status register 1 contains flags to signal these conditions:
SCTE — SCI Transmitter Empty Bit
TC — Transmission Complete Bit
SCRF — SCI Receiver Full Bit
IDLE — Receiver Idle Bit
Freescale Semiconductor
•
•
•
•
•
•
•
•
This clearable, read-only bit is set when the IRSCDR transfers a character to the transmit shift register.
SCTE can generate an SCI transmitter CPU interrupt request. When the SCTIE bit in IRSCC2 is set,
SCTE generates an SCI transmitter CPU interrupt request. In normal operation, clear the SCTE bit by
reading IRSCS1 with SCTE set and then writing to IRSCDR. Reset sets the SCTE bit.
This read-only bit is set when the SCTE bit is set, and no data, preamble, or break character is being
transmitted. TC generates an SCI transmitter CPU interrupt request if the TCIE bit in IRSCC2 is also
set. TC is automatically cleared when data, preamble or break is queued and ready to be sent. There
may be up to 1.5 transmitter clocks of latency between queueing data, preamble, and break and the
transmission actually starting. Reset sets the TC bit.
This clearable, read-only bit is set when the data in the receive shift register transfers to the SCI data
register. SCRF can generate an SCI receiver CPU interrupt request. When the SCRIE bit in IRSCC2
is set, SCRF generates a CPU interrupt request. In normal operation, clear the SCRF bit by reading
IRSCS1 with SCRF set and then reading the IRSCDR. Reset clears SCRF.
This clearable, read-only bit is set when 10 or 11 consecutive logic 1s appear on the receiver input.
IDLE generates an SCI receiver CPU interrupt request if the ILIE bit in IRSCC2 is also set. Clear the
IDLE bit by reading IRSCS1 with IDLE set and then reading the IRSCDR. After the receiver is enabled,
1 = IRSCDR data transferred to transmit shift register
0 = IRSCDR data not transferred to transmit shift register
1 = No transmission in progress
0 = Transmission in progress
1 = Received data available in IRSCDR
0 = Data not available in IRSCDR
Transfer of IRSCDR data to transmit shift register complete
Transmission complete
Transfer of receive shift register data to IRSCDR complete
Receiver input idle
Receiver overrun
Noisy data
Framing error
Parity error
Address:
Reset:
Read:
Write:
$0043
SCTE
Bit 7
1
Figure 12-15. IRSCI Status Register 1 (IRSCS1)
= Unimplemented
MC68HC908AP A-Family Data Sheet, Rev. 3
TC
6
1
SCRF
5
0
IDLE
4
0
OR
3
0
NF
2
0
FE
1
0
Bit 0
PE
0
I/O Registers
199