LPC2361FBD100,551 NXP Semiconductors, LPC2361FBD100,551 Datasheet - Page 12

• Manufacturer Part Number: LPC2361FBD100,551
• Description: IC ARM7 MCU FLASH 64K 100LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2300r

Specifications of LPC2361FBD100,551

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 100-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, Microwire, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 70
• Ram Size: 34K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC23
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 34 KB
• Interface Type: CAN/I2S/SPI/SSP/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 70
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 100LQFP
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4310 - EVAL BOARD LPC2158 W/LCDMCB2360UME - BOARD EVAL MCB2360 + ULINK-MEMCB2360U - BOARD EVAL MCB2360 + ULINK2568-4014 - BOARD EVAL FOR LPC236X ARM568-3999 - BOARD EVAL FOR LPC23 ARM MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4525; 935286991551

NXP Semiconductors
Table 3.
[1]
[2]
LPC2361_62_4
Product data sheet
Symbol
P4[28]/MAT2[0]/
TXD3
P4[29]/MAT2[1]/
RXD3
TDO
TDI
TMS
TRST
TCK
RTCK
RSTOUT
RESET
XTAL1
XTAL2
RTCX1
RTCX2
V
V
V
V
V
VREF
VBAT
SS
SSA
DD(3V3)
DD(DCDC)(3V3)
DDA
5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis.
5 V tolerant pad providing digital I/O functions (with TTL levels and hysteresis) and analog input. When configured as a DAC input,
digital section of the pad is disabled.
Pin description
Pin
82
85
1
2
3
4
5
100
14
17
22
23
16
18
15, 31,
41, 55,
72, 97,
83
11
28, 54,
71,
96
13, 42,
84
10
12
19
[1]
[1]
[1]
[1]
[1]
[11]
[1]
[1]
[7]
[8][9]
[8][9]
[8]
[8]
[10]
[12]
[13]
[14]
[14]
[14]
[1]
…continued
Type
I/O
O
O
I/O
O
I
O
I
I
I
I
I/O
O
I
I
O
I
O
I
I
I
I
I
I
I
Description
P4[28] — General purpose digital input/output pin.
MAT2[0] — Match output for Timer 2, channel 0.
TXD3 — Transmitter output for UART3.
P4[29] — General purpose digital input/output pin.
MAT2[1] — Match output for Timer 2, channel 1.
RXD3 — Receiver input for UART3.
TDO — Test Data out for JTAG interface.
TDI — Test Data in for JTAG interface.
TMS — Test Mode Select for JTAG interface.
TRST — Test Reset for JTAG interface.
TCK — Test Clock for JTAG interface. This clock must be slower than
CPU clock (CCLK) for the JTAG interface to operate
RTCK — JTAG interface control signal.
Note: LOW on this pin while RESET is LOW enables ETM pins (P2[9:0]) to operate
as trace port after reset.
RSTOUT — This is a 3.3 V pin. LOW on this pin indicates LPC2361/2362 being in
Reset state.
External reset input: A LOW on this pin resets the device, causing I/O ports and
peripherals to take on their default states, and processor execution to begin at
address 0. TTL with hysteresis, 5 V tolerant.
Input to the oscillator circuit and internal clock generator circuits.
Output from the oscillator amplifier.
Input to the RTC oscillator circuit.
Output from the RTC oscillator circuit.
ground: 0 V reference.
analog ground: 0 V reference. This should nominally be the same voltage as V
but should be isolated to minimize noise and error.
3.3 V supply voltage: This is the power supply voltage for the I/O ports.
3.3 V DC-to-DC converter supply voltage: This is the supply voltage for the
on-chip DC-to-DC converter only.
analog 3.3 V pad supply voltage: This should be nominally the same voltage as
V
power the ADC and DAC.
ADC reference: This should be nominally the same voltage as V
be isolated to minimize noise and error. Level on this pin is used as a reference for
ADC and DAC.
RTC power supply: 3.3 V on this pin supplies the power to the RTC peripheral.
DD(3V3)
but should be isolated to minimize noise and error. This voltage is used to
Rev. 04 — 4 March 2010
Single-chip 16-bit/32-bit MCU
LPC2361/62
© NXP B.V. 2010. All rights reserved.
DD(3V3)
1
⁄
6
but should
of the
12 of 57
SS
,