AT90USB646-MU Atmel, AT90USB646-MU Datasheet - Page 232

• Manufacturer Part Number: AT90USB646-MU
• Description: IC AVR MCU 64K 64QFN
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB646-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 48
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
• Processor Series: 90USB
• Core: AVR
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SPI, TWI, USART, USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Cpu Family: AT90
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Total Internal Ram Size: 4KB
• # I/os (max): 48
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: QFN EP
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: AT90USB646-16MU; AT90USB646-16MU

232
AT90USB64/128
Figure 20-12. Data Transfer in Master Transmitter Mode
A START condition is sent by writing the following value to TWCR:
TWEN must be set to enable the 2-wire Serial Interface, TWSTA must be written to one to trans-
mit a START condition and TWINT must be written to one to clear the TWINT Flag. The TWI will
then test the 2-wire Serial Bus and generate a START condition as soon as the bus becomes
free. After a START condition has been transmitted, the TWINT Flag is set by hardware, and the
status code in TWSR will be 0x08 (see
transmitted. This is done by writing SLA+W to TWDR. Thereafter the TWINT bit should be
cleared (by writing it to one) to continue the transfer. This is accomplished by writing the follow-
ing value to TWCR:
When SLA+W have been transmitted and an acknowledgement bit has been received, TWINT is
set again and a number of status codes in TWSR are possible. Possible status codes in Master
mode are 0x18, 0x20, or 0x38. The appropriate action to be taken for each of these status codes
is detailed in
When SLA+W has been successfully transmitted, a data packet should be transmitted. This is
done by writing the data byte to TWDR. TWDR must only be written when TWINT is high. If not,
the access will be discarded, and the Write Collision bit (TWWC) will be set in the TWCR Regis-
ter. After updating TWDR, the TWINT bit should be cleared (by writing it to one) to continue the
transfer. This is accomplished by writing the following value to TWCR:
This scheme is repeated until the last byte has been sent and the transfer is ended by generat-
ing a STOP condition or a repeated START condition. A STOP condition is generated by writing
the following value to TWCR:
A REPEATED START condition is generated by writing the following value to TWCR:
TWCR
value
TWCR
value
TWCR
value
TWCR
value
TWCR
value
SDA
SCL
TWINT
TWINT
TWINT
TWINT
TWINT
Table
1
1
1
1
1
20-3.
TRANSMITTER
Device 1
MASTER
TWEA
TWEA
TWEA
TWEA
TWEA
X
X
X
X
X
Device 2
TWSTA
TWSTA
TWSTA
TWSTA
TWSTA
RECEIVER
SLAVE
1
0
0
0
1
Table
TWSTO
TWSTO
TWSTO
TWSTO
TWSTO
Device 3
0
0
0
1
0
20-3). In order to enter MT mode, SLA+W must be
TWWC
TWWC
TWWC
TWWC
TWWC
........
X
X
X
X
X
Device n
TWEN
TWEN
TWEN
TWEN
TWEN
1
1
1
1
1
V
CC
R1
–
0
–
0
–
0
–
0
–
0
R2
TWIE
TWIE
TWIE
TWIE
TWIE
7593K–AVR–11/09
X
X
X
X
X