ATMEGA169V-1MC Atmel, ATMEGA169V-1MC Datasheet - Page 41

• Manufacturer Part Number: ATMEGA169V-1MC
• Description: IC MCU AVR 16K 1.8V 1MHZ 64-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169V-1MC

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 1MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-MLF®, 64-QFN
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Internal Voltage
Reference
Voltage Reference Enable
Signals and Start-up Time
2514H–AVR–05/03
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set if a Watchdog Reset occurs. The bit is reset by a Power-on Reset, or by
writing a logic zero to the flag.
• Bit 2 – BORF: Brown-out Reset Flag
This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by
writing a logic zero to the flag.
• Bit 1 – EXTRF: External Reset Flag
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by
writing a logic zero to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to
the flag.
To make use of the Reset Flags to identify a reset condition, the user should read and
then Reset the MCUSR as early as possible in the program. If the register is cleared
before another reset occurs, the source of the reset can be found by examining the
Reset Flags.
ATmega169 features an internal bandgap reference. This reference is used for Brown-
out Detection, and it can be used as an input to the Analog Comparator or the ADC.
The voltage reference has a start-up time that may influence the way it should be used.
The start-up time is given in Table 19. To save power, the reference is not always turned
on. The reference is on during the following situations:
1. When the BOD is enabled (by programming the BODLEVEL [2..0] Fuse).
2. When the bandgap reference is connected to the Analog Comparator (by setting
3. When the ADC is enabled.
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the
user must always allow the reference to start up before the output from the Analog Com-
parator or ADC is used. To reduce power consumption in Power-down mode, the user
can avoid the three conditions above to ensure that the reference is turned off before
entering Power-down mode.
Table 19. Internal Voltage Reference Characteristics
Note:
Symbol
V
t
I
the ACBG bit in ACSR).
BG
BG
BG
1. Values are guidelines only. Actual values are TBD.
Parameter
Bandgap reference voltage
Bandgap reference start-up time
Bandgap reference current
consumption
V
V
V
Condition
T
T
T
CC
CC
CC
A
A
A
= 25°C
= 25°C
= 25°C
= 2.7V,
= 2.7V,
= 2.7V,
(1)
ATmega169V/L
Min
1.0
Typ
1.1
40
15
Max
1.2
70
Units
µA
µs
V
41